good morning
what is the best used software in forward modeling for ground penetriting radar systems
There are many of them such as GPRSIM and the rest, but i think you can write your own programming code (using Python, C++ or Java) which will be an outstanding research work.
thanks mr kehinde but how
I think MATLAB may be a good choice. Anyway, please check the following:
https://www.researchgate.net/publication/317563768_Forward_Modeling_of_Ground_Penetrating_Radar_for_the_Reconstruction_of_Models_Response_Profiles_using_Synthetic_Data
https://www.researchgate.net/publication/236902011_Modelling_Ground-Penetrating_Radar_by_GprMax
https://www.huntergeophysics.com/product/gprsim-ground-penetrating-radar-simulation-software/
https://dl.acm.org/citation.cfm?id=1296595
thank you so much ms noha contrubing in this discussion
You can use MATGPR, Madagascar or MATLAB. They will do the job
Thank you s much
REFLEXW
good morning what is the best and the simple way to forward modeling in ground penetriting radar
03 April 2018 6,369 0 View
geometric classification of doline to appreciate karst evolution. Is it possible and how?
31 December 2015 2,341 2 View
Gravimetry and remote sensing structural studies
08 September 2014 10,073 3 View
CAN I USE THE BGI 5BUREAU GRAVIMETRIC INTERNATIONAL ) GRAVIMETRIC DATA FOR DETECTION OF DIAPIRISM PHENOMENA I HAVE GOT SOME POSITIVE RESULTS ABOUT THE SUBJET IN CENTRAL NORTH ALGERIA
08 September 2014 237 0 View
the computing of X,Y hilbert transformations composant using oasis montaj software gives 2 files with FHX,FHY grid extension wish software can read and transform these format to geosoft or surfer...
01 January 1970 706 2 View
Could you recommend some articles on Urban Transportation System optimization and Innovation?
13 August 2024 2,595 3 View
I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?
11 August 2024 3,115 1 View
I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...
10 August 2024 4,005 2 View
Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...
09 August 2024 7,892 0 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 719 0 View
Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...
06 August 2024 9,986 2 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View
I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...
05 August 2024 3,665 0 View
I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...
03 August 2024 6,028 4 View