There are several coated tools such as TiAlN and I am inquiring about the best of them to use in friction stir welding for metal matrix composite.
Looking forward your experience.
Can you please suggest me which media is best to isolate Campylobacter species?
09 January 2024 2,473 4 View
Nice Day I have the attached Energy dispersive spectroscopy (EDS) anaylsis figure but I am not having the good knowleage to read it carefully. Could please any one able to describe it? Is there...
21 August 2022 406 17 View
I would like to know what are the cybersecurity applications that depend on CVSS score to establish a defense mechanism for example or to determine the best action the defender may take. I know...
23 February 2021 8,028 3 View
I was at a broiler farm recently which had birds 3-day old broiler chick having leg problem. It was attirbuted to feed as DCP was added to the feed and the challenge reduce gradually, but could it...
15 January 2020 887 4 View
I am preferring to use Response Surface Methodology (RSM) in optimization of friction stir spot welding (FSSW) process, could you please tell me if there are any limitations to use this method in...
05 July 2018 5,537 8 View
I am planning to weld the maginsum alloys and Al alloys by friction stir welding, what is the expected limitations of that such the range of temperatures or plates thickness or pin geometry ...etc...
10 November 2017 7,110 1 View
Nowadays the applications of COMSOL software are expanding to many applications such add-on modules for Structural Mechanics, High and Low Frequency Electromagnetics, Fluid Flow, Heat Transfer,...
05 June 2017 3,253 0 View
Nowadays, the friction stir welding and friction stir spot welding are developing rapidly, so that can we see this type of friction replace normal types of welding?
01 June 2017 5,068 4 View
I prefer to use Arduino IDE inside the main code of c# to be able to control the Arduino from the main form of c#. I hope you can help
01 February 2017 6,895 0 View
I am working on project to use COMSOL software which using FEM to simulate spot welding for both friction stir spot welding (FSSW) and riestance spot welding (RSW), I am inquiring about the...
01 January 1970 3,515 1 View
How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...
10 August 2024 942 3 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
I did PR spin coating on trench structure. I used AZ P4620 PR and the thickness or PR is around 11um. The substrate is Si. And my trench structure depth is 141um(negative way). Even though I...
08 August 2024 2,298 0 View
One can try to generalize the Vandermonde determinant in the following direction: Let $A$ be any symmetric $n$-order square matrix. Consider its powers' diagonal elements $(A^k)_{ii}$ and...
08 August 2024 6,690 1 View
I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.
07 August 2024 4,526 4 View
Have you ever seen a LC-MS/MS method uses both internal standards and external standards (in matrix matching purpose) but the concentrations of internal standards are outside the calibration curve...
05 August 2024 3,084 6 View
- The Existence/Uniqueness of Solutions to Higher Order Linear Differential Equations - Higher Order Homogenous Differential Equations - Wronskian Determinants of $n$ Functions - Wronskian...
03 August 2024 2,366 0 View
I need to lyse and homogenise mouse tissues. So far I have experimented with liver and lung tissue, using matrix D. The liver was completely lysed with 6 repetitions of the standard program, but...
31 July 2024 9,186 0 View
We assume this to be true. Science leaves the era of mathematics and enters the era of matrix mechanics and the turning point is the discovery of numerical statistical theory called Cairo...
31 July 2024 3,900 2 View
I am new to Micromechanics and having similar problem with understanding the implementation of the formula's. I would appreciate if anyone can guide me on how to go about getting a scalar value...
30 July 2024 969 0 View