Any one have tutorials for Genie 2000 Gamma spectroscopy analysis software?

08 September 2017 8,776 3 View

How can i plot a radiation density map on a real site map? is there a certain software to do that?

08 September 2017 1,102 5 View

To manufacture a radioactive gamma emitting check (calibration) point source . What kind of physical tests and measurements needed?

01 February 2017 2,001 0 View

In calibration source fabrication how can i calculate the source effciency ?

31 December 2016 1,480 0 View

What is the mathematical relation to convert the radioactive dose rate to activity and vice versa?

10 November 2016 5,811 3 View

What is the best plan to start study theoretical nuclear physics by text books names if available?

04 May 2016 278 1 View

Is MCNP can be run in windows 10 - 32 bit ?

04 May 2016 8,904 0 View

What is the best text book in astrophysics?

31 December 2015 6,425 1 View

Is there a free software to calculate the neutron shield for many sources geometry?

31 December 2015 4,922 9 View

What is the best text book for C++ Programming?

31 December 2015 7,061 3 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

Physics: Why do we describe light by referring to its wavelength, but microwaves and radar pulses by referring to their frequency?

In physics, the description of the properties of light generally refers to its wavelength (nm), while in the range of microwaves and radio waves we refer to the frequency of a signal (e.g. kHz or...

03 March 2021 1,682 3 View

Could you recommend any books about Number Theory?

Beginner level books. High level books. Analytical Number Theory. Algebraic Number Theory. Combinatorical Number Theory. Books about partitions. Books about primes.

03 March 2021 7,174 5 View

What kind of intervention will be relevant to increase motivation among young sport trainees?

Any suggestion on what book to read is also welcome.

03 March 2021 1,646 4 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View