Any one have tutorials for Genie 2000 Gamma spectroscopy analysis software?

08 September 2017 8,776 3 View

How can i plot a radiation density map on a real site map? is there a certain software to do that?

08 September 2017 1,102 5 View

In calibration source fabrication how can i calculate the source effciency ?

31 December 2016 1,480 0 View

What is the mathematical relation to convert the radioactive dose rate to activity and vice versa?

10 November 2016 5,811 3 View

What is the best plan to start study theoretical nuclear physics by text books names if available?

04 May 2016 278 1 View

What is the best and simplest mathematics text book for physicists?

04 May 2016 364 1 View

Is MCNP can be run in windows 10 - 32 bit ?

04 May 2016 8,904 0 View

What is the best text book in astrophysics?

31 December 2015 6,425 1 View

Is there a free software to calculate the neutron shield for many sources geometry?

31 December 2015 4,922 9 View

What is the best text book for C++ Programming?

31 December 2015 7,061 3 View

Physics: Why do we describe light by referring to its wavelength, but microwaves and radar pulses by referring to their frequency?

In physics, the description of the properties of light generally refers to its wavelength (nm), while in the range of microwaves and radio waves we refer to the frequency of a signal (e.g. kHz or...

03 March 2021 1,682 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Why almost every element would be metallized in sufficiently high pressure and low temperature?

(This statement is from wikipedia, BTW). What is so special about metallic bond that is limiting high-P low-T state of a matter (as long as individual atoms exist, not white dwarf of neutron star...

02 March 2021 3,309 2 View

Which is the most convenient manufacturing software for Additive Manufacturing?

Which tools can be used to generate machine codes for additive manufacturing?

02 March 2021 7,220 2 View

What is the density for pva electrospining?

I'm Juan Carlos, a high school student who is working with electropinning, I made an electropinning machine with a 21g needle and a 30kv high voltage source and the distance between my needle is...

28 February 2021 298 3 View

Is anyone familiar with the cyclic compressive fatigue testing (BS EN 12697 - 25) ?

I would like to get more information on the cyclic compressive fatigue testing (BS EN 12697 - 25) which is typically done for bituminous material in pavement design. Any one can advise on the...

28 February 2021 2,004 3 View

Should we reduce the standard unit of length to 0.31951540592 meter ?

The reasoning behind this question is to align the ratios of the proton potential in energy per charge to the speed of light in distance per time. As these two dimensions appear to be related,...

27 February 2021 947 7 View

How do you mesh a thin solid in Fluent?

Hello, I have used the shell function on SpaceClaim to create thin solids for the model I am studying. These are contained within an enclosure for my study. I chose this approach as it avoids the...

24 February 2021 8,856 3 View

What software programs can directly simulate Additive Manufacturing Directed Energy Deposition (DED)?

I understand there are a lot of software programs that can simulate DED by going through specific modeling, simulation, and commands. For me, that was time consuming and results were not accurate....

24 February 2021 4,428 3 View

Standard curve shifting over time. How do I stabilise the ELISA?

24 February 2021 1,365 3 View