What is the best way to showcase a report (summary/proceedings of a conference) that you contributed to (and presented at the conference)?

I recently attended a conference, after which a summary report was published. The report summarizes each panelist's presentation (mine included), and the editor contacted each panelist after the...

14 June 2020 260 6 View

What is a Case Study and how should I do it?

For my dissertation (PhD) I am looking for something that does not require statistics per se. I am thinking of using a Case Study method. Can I use this for analyzing a group (Christian...

24 February 2020 6,951 4 View

Can I use human CD14+ freshly purified monocytes (without differentiating them) as APC in a Treg supression assay?

04 April 2017 8,284 4 View

Help with characterization of cre lines?

Help with characterization of cre lines?

06 December 2016 4,059 3 View

Does anyone know info or is a Soil scientist who has worked with phosphorus and phosphate rock in detail?

Changes in phosphorus with dissolution of Phosphate rock

09 August 2016 3,431 12 View

Any suggestions on which amino acids should the substitution of Thr and Ser result ?

Hi, I would like to generate a mutant of my protein by mutating its phosphorylated sites (a Thr and a Ser). To which AA can I best change these in order to get the least problems for my protein? I...

05 November 2015 5,251 2 View

Does anyone have any information on Moth re-introduction?

28 October 2014 382 3 View

How are changes in snowpack and snowmelt timing affecting soil moisture in mountainous regions?

I am looking at how soil properties and their responses to climate change affect forest cover. I think that in snow-dominated watersheds, the changes in snow dynamics have a great deal of...

25 December 2013 6,132 5 View

How does one determine protein concentration in mg/g FW?

I have done a standard curve for protein using BSA (absorbance vs ug/ml). How do I calculate the amount of protein in the cells in mg/g FW? I extracted 0.5g of cells in 2ml buffer and used 0.01ml...

01 October 2013 4,344 4 View

Nurse practitioner and physician assistant forums

I am writing research proposal that involves nurse practitioners and physician assistants, I have had little success on finding forums to post my survey, other than the usual social media sites....

01 January 1970 1,589 2 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View

I have designed reflectarray element and feeding it though Horn Antenna on HFSS. After full wave simulation, I am not getting desired results?

I have designed reflectarray element to generate OAM beams at 5.8GHz and feeding it though Horn Antenna on HFSS. After full wave simulation, i am not getting desired results i.e Radiation pattern...

01 March 2021 9,701 5 View

Can we distinguish the type of free fluid inside the pelvic and abdominal cavities whether blood or serous fluid using the ultrasound?

during ultrasound examination of acute abdomen, sometimes we see free fluid , can we know the type of fluid ,whether blood or not , using ultrasound only? if yes , what are the sonographic...

01 March 2021 7,476 4 View

How much pressure we can reduce at the outlet to avoid Reverse Flow?

I am simulating Heat Exchanger. I have tried and tested all the methods to resolve this issue from the internet like refining mesh, improving skewness and orthogonal quality ,extending outlet to...

01 March 2021 6,985 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

Is there a method of determining feed digestibility without the need to re-pellet the feed?

I am aiming to determine the ADC values of a commercial fish feed, but I do not have a steam pelleter or extruder available to me. Ideally, the pellets could be coated with some inert marker....

28 February 2021 7,967 3 View

Can anyone help me with the administration of the "Mind the Gap" Scale for satisfaction with transition to adult care?

We are working on a study focused on adolescents' transition to adult care and are looking for a validated measure for satisfaction with the transition. So far the only measure that we have came...

28 February 2021 2,338 1 View

How to calculate Ligand-active site distance in a ligand-protein complex from MD simulation?

I have run a MD simulation of a ligand-protein complex in GROMACS using CHARMM forcefield. Reviewer has asked me to calculate Ligand-activesite distance and binding free energy of ligand with...

27 February 2021 4,703 1 View