Problems in modelling suction cavitation at low pressure in ANSYS FLUENT?

Hi all, Problem statement: I am trying to model water cavitation using Singhal model in fluent. Geometry : ( Pipe converges from 50 mm to 5mm-orifice). This pipe is on the suction side of the...

08 September 2017 5,104 0 View

How to model a tensile coupon with pores normally distributed along the volume in ANSYS/ABAQUS?

model a tensile coupon with pores normally distributed along the Volume? Pore distribution details were obtained using x-ray tomography.

11 December 2016 4,605 1 View

Hi can i know is anyone doing Quasi static indentation testing in abaqus?

I am doing a quasi static indentation testing using abaqus.. And i always get an error, time increment is too big.... How can i solve this error please help me. I tried adjusting the time period...

31 December 2015 153 9 View

Can polymer concentrations be calculated based on the number average molecular weight?

Hello, I spin-cast two different polymers onto wafers and measure their height as a function of initial concentration. For polymer A, I have the weight-average molecular weight (Mw) as well as...

28 February 2021 7,882 2 View

RIA. How to measure?

When you use RIA, with a control the unknown sample with antibodies, you bare in mind the binding sites of the antibodies. However you still need to measure labelled antigen (radioactive) and not...

28 February 2021 2,133 3 View

How to Eliminate cosine error and abbe error in LASER measurement system(for example Rhenishaw XL80)?

I like to do project in laser measurement system. My objective is to eliminate or reduce the cosine error, abbe error in Laser measurement system. I have Rhenishaw XL80 system. Please tell the...

28 February 2021 4,890 3 View

How to measure angle between laser travel path and machine axis in Laser Measurement system?

25 February 2021 1,987 3 View

How to resolve Gaussian error termination " Error termination via Lnk1e in F:\G16W\l103.exe" for TS(QST3)?

When I run the job for TS(QST3) in gaseous phase, it was completed without any error. But when I add water in CPCM model it terminated with an error: Inconsistency: ModMin= 2 Eigenvalue=...

21 February 2021 3,198 2 View

Could the "incoming radiation (net radiation)" values be negative?

Could the "incoming solar radiation" values be negative? What is the difference between "global solar radiation" and "incoming solar radiation"? Which one might be measured negative values?

21 February 2021 7,726 9 View

Using the Pfaffl method: Is it possible that the ratio of the calibrator does not equal 1?

Hi all, I have a question regarding calculations using the Pfaffl method. I have 3 groups per experiment: 1 control group (calibrator) and 2 treatment groups with 6 to 7 biological repeats per...

19 February 2021 8,351 2 View

Can I follow Researchers from Teaching and testing areas?

I want Researchers from Educational Measurement and Evaluation, relating to teaching, learning , academic performance and test validation

18 February 2021 4,757 13 View

How can I measure the surface interaction or surface interfacial chemistry between polishing abrasives and upper surface of substrate ?

I am working on polishing abrasives. I need to do few characterizations ? which can provide the on time surface chemistry of substrate with polishing abrasive during optical polishing. I would...

18 February 2021 5,319 3 View

How to get rough estimation of the concentrations of Oxygen and moisture inside the glove box?

Dear colleagues, I was just wondering if you can suggest a good method to get a rough estimation to the concentration of O2 and H2O inside the glove box as unfortunately, our glove box doesn't...

17 February 2021 1,012 3 View