What is Fermi level of CeO2 in eV?

Suhail Anjum Abdur Raheem Sayyed @Suhail_Anjum_Sayyed

06 June 2016 0 3K Report

what is the value of Fermi level of CeO2?

How to calculate it theorotically and practically?

Badges
Science topic

More Suhail Anjum Abdur Raheem Sayyed's questions See All

How to use MOSFET for IV measurement?

Respected sir, We are making IV measurement setup. To the Gate of MOSFET, we give voltage in steps (VGS). and at the same time, we check the voltage at drain (VD) w.r.t. ground. It is varying but...

02 March 2019 5,242 3 View

Please suggest some nanoparticles whose chages drastically before and after oxidised state?

Please suggest some nanoparticles whose chages drastically before and after oxidised state? Also, suggest methods of sysnthesis.

11 December 2018 329 6 View

How much is the porosity of TiO2 films and CeO2 films as photoanode in dye sensitized solar cells?

As in DSSCs porous structure of photo-anode is one of the major factor for performance. How much is the porosity of TiO2 photo-anode? and What will happen to porosity if we make CeO2 photo-anode?

07 August 2016 3,499 4 View

What are the effects of annealling on nanomaterials?

specially for wide band gap oxides such as CeO2.

01 February 2016 2,002 4 View

How can I improve short circuit current in Dye Sensitized Solar Cells?

The solar cells we are making are having good voltage arouen 350 to 500mV but current is low in microAmpere. How to improve current. we are using low cost dyes such as rose bengal and eosing y.

02 March 2015 3,249 19 View

Dear All is DIgSILENT PowerFactory (14.1.3) a free or is demo available. if so please send me the link.

Dear All is DIgSILENT PowerFactory (14.1.3) useful for simulation of DSSCs a free or is demo available. if so please send me the link.

08 September 2014 7,351 7 View

Is it possible to plot the atom-projected band structure using GPAW?

Hi, I'm currently working on a project where I need to plot the atom-projected band structure using GPAW. I've been able to calculate the band structure for my material, but I'm having trouble...

07 August 2024 269 3 View

¿Are oxygen vacancies in semiconductors capable to change the band gap?

Dear all! Oxygen vacancies do raise negatively the Fermi level by increasing the negative charge in the semiconductor crystal structure. In the case of n-type semiconductors, I wonder if this...

30 July 2024 8,339 2 View

Why Orca calculations take too loong?

Hello! I am trying to calculate the sumatriptan molecule, but it has been counting for five days and it does not stop. It seems to me that it is too long and I am doing something wrong. Please...

25 July 2024 3,364 5 View

MDCI module in Orca software?

Dear Researchers, My question is associated with the "MDCI" method in Orca. Please let me clarify my question using a simple example: Suppose we are going to perform CBS extrapolation using "!...

21 July 2024 1,632 0 View

Should a defect induced structure be optimized in a DFT calculation?

I'm trying to study the effects of introducing vacancy defects in my material. If I optimize my structure and find the lattice parameter before introducing vacancy, should I again optimize my...

18 July 2024 1,794 2 View

What is the recommended type of pseudopotentials for QE?

Hello dear colleagues and professors Please what is the recommended type of pseudopotentials for QE? ultrasoft or norm conserving?? And from where get all types of pseudos (us, nc, pbe,...

09 July 2024 9,541 5 View

What to do for Error termination via Lnk1e in /share/apps/gaussian/g16/l502.exe, for Ce through B3LYP/SDD?

I am trying for the structure optimization via Gaussian16 DFT calculation, for a system consisting of C,H, N, O and Ce atoms. Where I am using B3LYP/ 6,311G(d,p) C, H, N and O and B3LYP/SDD for...

30 June 2024 9,979 4 View

Which free software is preferable for DFT calculations?

I want to perform DFT calculations for a triple cation mixed crystal. Which software is preferable and free?

28 June 2024 5,255 2 View

Can someone help me to model a core-shell nanostructure in GDIS and subsequently prepare the fdf file for using in SIESTA?

I am very new to the material modelling in GDIS. So, I want to learn how to model a nanostructure specifically core-shell in GDIS.

28 June 2024 5,224 0 View

How to do DFT calculations and which free software is easy recommended for that?

i want to do DFT calculations for a triple cation mixed crystal. Can somebody help me in this regard?

27 June 2024 1,804 0 View