What is Extended describing functions (EDF) ?

14 August 2019 0 1K Report

In LLC Resonant converts i can apply in small signal modeling using Extended describing function (EDF) ? Why not applying for Average modeling in LLC resonant converters ?

Badges
Science topic

Similar topics
Engineering
Modeling

More Kuruva Veeranna's questions See All

SPWM génération triangular wave ?

Dear Friends, Can you see the waveforms? If we use PWM generation with a sine wave and a triangular wave ranging from 0 to 1 If we use PWM generation with a sine wave and a triangular wave ranging...

21 May 2024 5,439 2 View

How to calculate the Dead time for application of three phase grid connected Inverter ?

Hi All How to calculate the dead time for application of three phase grid connected Inverter suppose my Switching is frequency 4Khz. I considered the dead time 3.3 – 4.3 µs for the for...

09 December 2023 6,892 1 View

I am working on LCL grid connected Inverter ?

Hi All I am working on LCL Grid connected inverter. My question is I am getting good grid current (THD

22 November 2023 379 3 View

How to attenuates low frequencies for grid current (Grid connecetd inverter) ?

Hello All We using Grid connecetd Inverter using LCL Filter, we are unble damp low fréquences (like 200 hz to 350 hz) Can you please suggest How to attenuates low frequencies for grid...

12 November 2023 8,392 5 View

Regarding How to calculate the participation factors based on the eigenvalues ?

Hi all Can you please suggest me How to calculate participation factors based on the eigenvalues real and complex. 1. Eigenvalues 1.0e+03 * -0.034236848980183 + 6.751951884207693i...

24 August 2023 4,686 2 View

Design parameters Dual active Bridge Leakage Inudtance, Input Capaciatnec (Cin), Output Capaciatnec (Cout) ?

Hi Friends, In Dual Active Bridge (DAB) design of Leakage inductance, Input Capacitance (Cin), Output Capacitance (Cout) formulas and How will effect Gain Vs Phase shift formulas, Can you...

08 June 2021 4,311 3 View

In Open Loop control interior PMSM/ Induction motor how will give excition vd, vq ?

Hi friends In open Loop control of interior PMSM/Induction motor how will give excition vd, vq and any mathematics is there inside to give vd ,vq Can you send me any related to paper .

30 May 2021 9,660 2 View

Why Current control is faster than voltage control ?

Hi friends Why Current control( inner loop) is faster than voltage control ( outer loop) in power converters ? Can you explain me deep level.

29 May 2021 5,822 4 View

What is the Purpose of Vd=0, Vq=1, in surface PMSM and Vd=1, Vq=1 Interior PMSM, Induction Motor ?

Hi Friends , 1.What is the reason of Vd=0, Vq=1, in surface PMSM and Vd=1, Vq=1 Interior PMSM, Induction Motor ? behind that any back ground can you explain....

27 May 2021 1,890 1 View

What is the Spaces vector modulation_Top Pwm and Space vector modulation_Bottom Pwm ?

Hi friends Can you help me What is the Spaces vector modulation_Top Pwm and Space vector modulation_Bottom 1. How to implement SVM_Top and _SVM_Bottom in three phase inverter 2. I know...

20 May 2021 775 2 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

Is it necessary to covary exogenous constructs in a structural model?

I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...

03 August 2024 6,028 4 View

How to correctly use the UTE and ZTE pulse sequences in Bruker's ParaVision software?

I am using a Bruker 600M solid-state NMR spectrometer with a Micro 2.5 microimaging system. The test sample is a tube of 1M LiCl aqueous solution, and the nucleus detected is 1H. I am trying to...

01 August 2024 9,227 1 View