What is correlation between fracture toughness and other mechanical properties of 300M low alloy high strength steel?

11 November 2017 0 2K Report

To all research gate fellows;

I apologise for not writing the material grade in my previous question, it is 4340 modified 300M low alloy ultra high strength steel.

Regards

Shivraj Singh Kasana

Badges
Science topic

More Shivraj SINGH Kasana's questions See All

What microstructural and physical changes will happen if high hardenability steel sample after quenching is kept for self aging for six months?

To study the effect of self aging in low alloy medium carbon steels and high chromium air hardening martensitic stainless steels, various steel grade samples are under study in my research...

06 July 2019 6,949 7 View

How we can determine critical temperatures like ac1,ac3,Ms Mf and liquidus temperature of a steel alloy by thermo mechanical simulator?

In my experimental alloy I want to calculate the actual critical temperatures of alloy steel like ac1.ac3.Bs. Bf, Ms,Mf,liquidus and solidus temperature by TMS GLEEBLE 3800.This will help me in...

04 May 2018 2,500 8 View

Upto what minimum grain diameter we can achieve by severe plastic deformation in ultra high strength steels?

I wish to utilize all possible strengthening mechanism in developing a unique ultra high strength nano bainitic steel

04 May 2018 8,292 2 View

How much time journal of Materials processing and technology takes to publish a paper?

Is is about publishing a paper in suitable journals

03 April 2018 2,129 2 View

How to prevent microstructural banding in medium carbon nickel chrome moly low alloy steels?

Severe microstructural banding is observed in HSLA nickel ,chrome moly steel rolled bars which is not removed by hardening and tempering. and results in poor high cycle fatigue properties.This is...

03 April 2018 2,064 1 View

In which countries people celebrate festival of colours called HOLI like in India?

Holi the festival of playing with colours with each other is played in India .BARSANA a plce near Mathura is famous for Lath maar holi from radha-krishna times.HAPPY HOLI TO all fellow researchers...

02 March 2018 6,239 0 View

We are using HHA steel plate with hard armor and soft armor panels to resist ballistic test by hard steel core projectile can someone tell is it ok?

In construction of bullet proof jacket 600 BHN quenched and tempered low alloy UHSS steel sheet of 3mm thickness is used in strike face followed by HAP and SAP made by high density polyethelene...

01 February 2018 7,911 0 View

If warm bending of high hardness armor sheets are bended ,can some body tell how much time plates should be heated before warm bending?

Required for my project

31 December 2017 10,012 2 View

When calculating Ms and Bs temperature of an hypereutectoid low alloy steel Ifound that Ms and Bf temperatures are different why so?

In absence of dilatometer and other facilities I wish to estimate my heat treatment temperature by emperical formulae available but find difference of about 84 deg.C in Bf and Ms,what should Ido?

31 December 2017 2,886 0 View

How we can improve weld properties and reduce HAZ in welding of high hardness armor steel plates?

Since fabrication by bending and welding is required in construction of armor protection structures made from high hardness ultra high strength armor steels a thorough understanding of these...

31 December 2017 3,592 4 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Is there anyone with experience in TEM analysis who can assist with a manuscript for an upcoming journal?

Hello dear colleagues, We have prepared a manuscript on NiTi-based alloys and are seeking a second opinion on our current TEM results. If you are a Ph.D. holder with experience in TEM and have...

07 August 2024 9,563 0 View

How does grain and grain boundary affect the ceramic when studying its dielectric properties?

I am not able to get good literature and the physics behind how first these grains and grain boundaries arises out of no where when we make a pellet to study its dielectric properties and then how...

07 August 2024 5,177 3 View

How to report results of Generalised Linear Mixed Models in a journal article?

Hi everyone, If you have written or come across any papers where Generalised Linear Mixed Models are used to examine intervention (e.g., in mental health) efficacy, could you please share the...

04 August 2024 4,130 4 View

The question is how to use Wavenet transform?

HOW CAN I WRITE A CODE TO USE THE WAVENET TRANSFORM AS A FEATURE EXTRACTION METHOD INSTEAD OF DWT IN MATLAB?

03 August 2024 7,829 0 View

Can't spin-orbit coupling(SOC) be included in optical properties calculation in CASTEP?

I am currently using CASTEP version 2020. When I want to run optical properties calculations with spin-orbit coupling(SOC), I encounter the following error in a pop-up window before the job gets...

02 August 2024 2,890 0 View

How select composition for ods-high entropy alloys?

31 July 2024 2,795 1 View

What should be the sample container for the hydrothermal reaction in a microwave reactor at 180 °C for 10 min at the heating rate of 5 °C per minute?

Suggest one of them 1. Teflon-lined stainless steel autoclave: 2. Alumina (Al2O3) ceramic container

30 July 2024 7,326 1 View

What should a Mechanical Engineering PhD scholar focus on during their PhD to enhance their chances of securing a postdoctoral position?

29 July 2024 7,714 4 View