I want to use nanotechnology for waste leachate treatment. I have to learn about the typical processing sequence of stages and then apply nanotechnology in order to eliminate some of the stages or combine some other ones
Dear Dr. Farzane-Besharat:
There are a set of processes and procedures assigned to "leachate-treatments".
it is possible to gain further insight in:
https://www.gov.uk/government/uploads/system/uploads/attachment_data/file/322412/Guidance_for_the_Treatment_of_Landfill_Leachate_part_2.pdf
The pdf document is attached; in this document exist a step involving "liquid", with units mg/l, the magnitude is commonly great 100,000 to 200,000.
Kind regards
Marcos Nobre
Thank you so much Dr. Marcos Nobre. So kind of you.
adding graphene oxide / rGO / graphene have shown conflicting surface roughness changes in Polyethersulfone. for rGO in specific, why do we have roughness decrease whilst porosity has increased?
01 February 2019 9,732 5 View
GO in NMP - considering NMP is not an electrilyte on itself, can the flakes move towards the opposite electrode?
08 September 2018 9,349 0 View
when the loadings of GO in the polymer increased the contacact angle was almost the same as the pure polymer and in one case higher... what can be the reason ... it is expected to have more...
04 May 2018 8,063 3 View
when I apply an electric field over my polymer solution it tries to move toward the negative electrode (the distance between the two electrodes is very low) this local movement is different every...
02 March 2018 10,092 4 View
while casting a carbon filler /polymer composite membrane on glass, during inversion in water , it gets up with a convex surface which is a little shiny. is this side the top surface of the...
01 February 2018 8,022 9 View
when i want to try thick sectioning of my sample, I fill in the tray with water bu even with angular and axial regulations and also filling and vacuuming water , it does not wet the upper part !...
31 December 2017 6,494 6 View
I need to cover a metal surface with a thin layer of a water soluble polymer and this layer should adhere very well and not separate , also no-toxic ... what are the feasible methods?please...
31 December 2017 3,747 10 View
I need to know the viscosity and dielectric of my solution. (polymer in a polar solvent)please advise if there is simple models or estimation techniques just to know an approximate estimation
31 December 2017 6,046 2 View
my membranes are produced about 4.5 cm . is it possible to test them by a sterlitech HP4750 cell with some modifications of the setup?
11 December 2017 3,862 2 View
when we are using phase inversion method, how can we avoid formation of holes in the film casting on a glass slide? what parameters are effective?
09 October 2017 4,788 1 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
Hello, Can anyone provide me with the absorption coefficient of methane gas at 7.7 um? Any reference?
06 August 2024 980 5 View
Hello. I am working on ROS production of two systems: system A is cerium oxide and hydrogen peroxide, system B is cerium oxide nanoparticle, hydrogen peroxide and potassium bromide. I did some...
04 August 2024 5,974 3 View
I conducted an adsorption experiment of arsenic on soil in the presence of different doses of silicon as competing ions to see the effect of silicon on arsenic adsorption and desorption. I took 5...
03 August 2024 6,500 3 View
Hello, colleagues. Recently, I have been working on a metal processing simulation with my UMAT in Abaqus. I have outlined the corresponding simulation, but I keep encountering issues that cause...
30 July 2024 7,062 1 View
I am looking for a lipid waste disposal method, keeping in mind the environmental, health and safety aspect of lipid waste. Could someone please provide guidelines or the lowest acceptable...
25 July 2024 637 5 View
In running two-dimensional gel electrophoresis on bacterial protein, some spots that appear to match a protein sequence have a significantly more acidic isoelectric point than the calculated pI....
24 July 2024 8,076 3 View
// interested in the difference between floating events and short circuits.
22 July 2024 6,565 0 View
I know the rate law. But for my photo-catalytic experiments, first 90min is adsorption (dark) and next 150min is under UV light (total 240min). How to remove the adsorption part for calculation?...
21 July 2024 8,807 6 View
Is it reasonable to exclude all trials with a blink or saccade in the 150 ms before stimulus onset? As an alternative, would it be better to exclude blinks (after extending them by about 100 ms...
19 July 2024 3,838 0 View