What are the suitable models for EIS of PEM fuel cells?

More Laya Das's questions See All

Is it possible to have repeated eigenvalues and linearly independent eigenvectors corresponding to the repeated values?

Is it possible to have a matrix A which is invertible, and has repeated eigenvalues at, say, 1 and still has linearly independent eigenvectors corresponding to the repeated values? I require any...

07 August 2016 8,061 12 View

What is the difference between the autocorrelation of a stationary signal and non-stationary signal?

If one takes the autocorrelation of a stationary signal, and then that of a non-stationary signal, then would it be possible to say which one is stationary from the ACFs?

31 December 2014 9,893 5 View

What is the geometrical interpretation of multiplying a matrix by the inverse of another matrix?

What happens geometrically when one multiplies a matrix A by the inverse of a matrix B?

31 December 2014 5,457 5 View

What is the advantage of multivariate change point detection over univariate change point detection?

In a multivariate time series, what extra information does performing multivariate change point detection provide than performing univariate change point detection of individual time series? Both...

11 December 2014 5,549 3 View

How should I handle zero R2 values?

Consider a time series (stationary or non-stationary). I fit a linear model of order 0, i.e., an intercept to the data. In the stationary case, this corresponds to the mean. Now, when I calculate...

10 November 2014 7,293 13 View

How can one identify a wrong parameter in a state space model?

I have a state space model - linear or non-linear. I know that there is (are) wrong parameter(s) in the model (the model structure is correct though). Is there a method to isolate the wrong...

09 October 2014 2,805 6 View

What is the discrete equivalent of complex conjugate poles on imaginary axis for continuous case?

If there are complex conjugate poles on the imaginary axis (+jw and -jw) for a continuous system, what would be the location of the poles of the equivalent discrete time system?

08 September 2014 4,386 5 View

What measures exist for characterising and classifying segments of data acquired over a period of time?

I have measurements from a system over a long period of time. During this time, the system has been in different states (for example, different controller tuning configurations). Now, looking at...

07 August 2014 3,606 7 View

Performance of EKF changes with noise in MATLAB?

When I change the seed of random noise generation in MATLAB, keeping everything else fixed, the performance of the EKF and also UKF (MSE, ACF of the estimation errors, etc.) changes every time....

01 February 2014 1,910 16 View

What is the effect of DC on fft in MATLAB?

What would be the effect of a dc component on the fft of a signal with time varying frequency content?

01 February 2014 4,625 3 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

Why Do TDS and EC Increase with Larger Wastewater Volumes, While BOD and COD Decrease?

I have carried out MFC experiments on three different volumes, 50, 500 and 1000 mL of wastewater. Results after MFC treatment shows that TDS and EC are more in larger volumes of water i.e. TDS and...

09 August 2024 9,621 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Is there any way to quantify bacterial and fungal cells in their mixed culture?

I am working in fungal fermentation of soybean meal and there is bacterial growth in them at times. I am trying to quantify fungal cell counts and bacterial cells; but I haven't been able to do at...

07 August 2024 7,535 4 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

What procedure should I follow for current controlled PPy film electrochemical deposition on ITO?

For example, I perform passivation process before electropolymerization of Py for adhesion to titanium surface. Is a similar or different procedure required for ITO? If necessary, I would be glad...

06 August 2024 3,176 0 View

Why activated CAR-Jurkat cell could not kill targets?

Previously when I co-coluture anti-CD19(FMC63) CAR-Jurkat with Raji with E:T=5:1, Jurkat can eliminate Raji in 24h. However, when I test another CAR construct, although I can dectect totally CD69...

06 August 2024 641 2 View