How to estimate 2SLS with different instruments for different endogenous variables?

To be specific, I want to conduct an IV regression in stata with the following three equations. EQ1: Y1 ~Y2 Y3 X EQ2: Y2 ~ Z1 EQ3: Y3 ~ Z2 Both Y2 and Y3 are endogenous. However, Z1 and Z2 are...

23 February 2021 6,266 3 View

Hi, Good day! Do you have related studies about my title, "Factors Affecting the Senior High School Students' Stress Tolerance in Problem Solving"?

I am new researcher. I want to learn more and I need your help. Thank you.

04 February 2021 6,834 4 View

How to take p-xrd sodiated carbon anode material?

Can i collect p-xrd data of sodiated carbon anode of sodium ion battery in presence of air? Or I have to do the xrd in inert atmosphere?

23 January 2021 3,506 2 View

How to calculate the degradation rate in percentage ?

I performed the BCA assay to calculate protein content over the time period. However, I'm not understanding how I can calculate the degradation rate in percentage at each time point? What formula...

10 January 2021 9,094 3 View

How do moisture and air contribute to the capcity fading of fabricated anode materials for Na-ion batteries?

I am using a glove box with N2 supply for Na ion battery coin cell assembly. But the oxygen level is more than 20 ppm. Can anyone one suggest whether 20ppm oxygen level is okay for battery...

15 November 2020 5,727 3 View

How to design a PI controller for fourth-order transfer-function ?

Hey! I'm in the work of designing a controller for a zeta converter, it is a fourth-order system. I tried ways like the Ziegler-Nicols method, Root locus method using Control System Designer in...

29 October 2020 4,054 3 View

How to cite the results from Gallup Strengths Finder Assessment?

In my report, I included the ideas from the results given to me by the Gallup Assessment, but I am confused on how I will cite the website using APA 6th edition and what is the format for both the...

12 October 2020 5,396 2 View

Is it possible to get more than one final optimal solution using TOPSIS decision-making method in multi-objective optimization problem?

So is it possible to get more than one final optimal solution using TOPSIS decision-making method in multi-objective optimization problem? If there is the possibility of getting more then one...

01 September 2020 7,680 9 View

Probe based primers for conventional PCR?

27 August 2020 1,935 2 View

How are latent means and observed composite means different?

I know that they are different but I am kind of at a loss for how to explain the difference, but I may be overthinking it. In simple terms, my understanding is that a latent mean(intercept) is an...

19 August 2020 8,857 4 View

What software programs can directly simulate Additive Manufacturing Directed Energy Deposition (DED)?

I understand there are a lot of software programs that can simulate DED by going through specific modeling, simulation, and commands. For me, that was time consuming and results were not accurate....

24 February 2021 4,428 3 View

Which software is best to analyse multi-phase fluid flows ?

Hello everyone, hope all is good. I want to analyse multi-phase fluid flow through pipe, which software is best to do so ?

21 February 2021 4,230 8 View

2D wavelet transform?

Dear all I have a 2-dimensional mode shape of one concrete beam and I put the data of mode shape in a matrix (69*3) which the first column in the matrix is x coordination of my beam and the second...

10 February 2021 3,301 3 View

Inquiry regarding engineering journals for free publications for my dissertation (laser polishing of 3D printed parts?

my dissertation was on laser polishing of 3D printed plastic parts, i want to publish it, can anyone suggest me a free copy engineer journal for this purpos, plz?

01 February 2021 7,140 4 View

How can I stain 3d printed cells in hydrogel without damaging the gel?

I tried staining my cells in a gel using standard protocols with 4PF% for fixation and triton-X or saponin for permeabilization but the gel always gets damaged throughout the steps, and at the end...

17 January 2021 4,170 1 View

Method to measure printed layer thickness on paper substrate ?

I want to measure thickness of screen printed graphene ink on paper substrate. Can anyone suggest any accurate and feasible method to measure it. I tried profilometry (stylus & optical) but...

11 January 2021 6,179 6 View

A three electrode sensor inkjet printed gets damaged in few hours of usage in a dynamic media flow chip, any solution for that?

We are using some biosensors which are inkjet printed and are used in the microfluidic chip where media is flowing at the flow rate of around 60 uL/min. However, after the continuous use of few...

05 January 2021 610 2 View

Future of construction systems?

Do you think that the automatized 3D-printing technique will replace the traditional building method?

10 December 2020 2,052 12 View

Kinetic modelling of oxidative dehydrogenation of ethane ?

According to below articles about kinetic modelling of ODH reactions by G. Che-Galicia and et al. there are some problems need your guidance and advices: Kinetic and reactor performance of a...

27 November 2020 9,035 3 View

My customized ink is pulsating but not jetting out of cartridge nozzle of Dimatix2831 inkjet printer, droplets just seem to hang from the nozzle. Why?

I am having trouble printing with the Dimatix 2831 inkjet printer. The nozzles seem to be pulsating but they are not jetting, the droplets just seem to be hanging from the nozzles. What could be...

23 November 2020 9,136 6 View