Is their any procedure to produce genetic knock out lab animals?

I would like to design knock out mice for PCOS, Suggest me suitable articles/ procedures.

05 June 2018 5,460 0 View

What are the poly herbal liquid formulation standardization methods?

Is there any official standard for standardization of poly herbal liquid formulation.

03 April 2018 6,432 2 View

What is the procedure to calculate animal dose for Green synthesized nano particle?

Is their any specific OECD guidelines or any other procedure?

01 February 2018 8,954 2 View

Is there any work in relation to polyherbal formulation with nanoparticles?

Require reference about formulation of polyherbal preparation with green synthesized nano particles.

31 December 2017 6,463 4 View

Is it possible to synthesise nano particles from plant isolate ( olieolinc acid)?

We have a olieolinc acid isolated from herbal extract, want to make a nano formulation. Is it possible?

10 November 2017 7,343 0 View

Heat exchanger with liquid Nitrogen as coolant?

I want to cool Natural Gas from 195 Kelvin to 138 Klevin in a heat exchanger by using liquid nitrogen as the coolant medium. When entering the heat exchanger, the liquid nitrogen will have a...

01 March 2021 6,450 5 View

How to get/count refractive index in gasses?

20 February 2021 8,202 6 View

How to improve dissolution of neosome?

I have made neosome from herbal drug. Neosomes are stable. But I face problems in dissolution. I used minimum ratio of 1:1:0.25 ( Drug:span 60: Cholesterol and GMs. Now how can I active better...

17 February 2021 3,584 1 View

How to make Fast Green FCF from powder?

Hi everyone We need Fast Green to electroporate plasmid into mice embryos, therefore we simply need it to see some color in the liquid we are electroporating so that electroporation is more...

07 February 2021 1,671 2 View

Which is the best software for the simulation of tribological properties of materials?

I want to simulate the tribological properties of solids, liquids, and fluids, please suggest good software.

02 February 2021 3,947 3 View

Does anybody work with CoolLED in fluorescence microscopy?

I have trouble with exciting wavelengths higher than 460 nm while e.g. ex with 405 nm works. Filtercubes are correc, as I used them with my old xenon lamp before... I work on axiovert200M and with...

25 January 2021 5,201 2 View

How to prepare a liquid sample for FTIR spectrum?

I have a ethanol-water 50% extract of mango peel. I purified mangiferin from the extract with filtration and precipitation. so i obtained a low concentrated extract which i want to se the IR...

24 January 2021 8,880 7 View

Why high voltage and current (and some gases) Cause Spray-mode metal transfer in Gas-Metal Arc Welding (GMAW)?

This transition phenomena of Globular to spray mode as voltage , and especially current is raised, is very commonly known to Manual Metal Arc Welding (MMAW) and Gas-Metal Arc Welding (GMAW)...

20 January 2021 7,984 2 View

Can you have pressure inlet and velocity inlet at the same time?

I was reading a reference (Reitz-A Photographic Study of Flash Boiling Atomization). In his experiment, his boundary condition is delta p and constant velocity. The liquid injection pressure was...

18 January 2021 842 9 View

How to interpret the result of agar well diffusion assay using herbal extract?

I performed the antibacterial activity of isolated herbal extract against Rhodococcus equi and used Erythromycin as a standard drug, ZOI of the plant extracts were 16-20mm and Erythromycin was 28...

17 January 2021 1,746 3 View