Interface properties between CNT and polymer affects the elastic modulus of the CNFRP.It will be great if any one can provide the interface properties between CNT and ABS polymer.Thank You
Please check these references, might be helpful for you.
http://onlinelibrary.wiley.com/doi/10.1002/polb.23129/abstract
http://iopscience.iop.org/0022-3727/46/38/385305
http://pubs.acs.org/doi/abs/10.1021/am5056849
http://pubs.acs.org/doi/abs/10.1021/am501879q
http://www.polymer.cn/UploadFile/research/201310271956488182.pdf
http://www.sciencedirect.com/science/article/pii/S0921452613001233
In case of plane stress and plane strain , the biharmonic equation roots will be different as the Hooke's law is different for both the cases. So, I would like to ask can we use same complex...
03 April 2018 1,925 4 View
I am trying to do failure analysis of randomly distributed CNT reinforced composite.Please suggest me how to incorporate the interface properties between polymer matrix and carbon nano tube in...
01 February 2015 5,188 10 View
In multi scale modeling, what are the deciding factors that dictates selection of particular scale of modeling ?
07 August 2014 1,204 8 View
I have a model designed in creo 2.0. I want to model it as fiber reinforced composite for analysis .Please let me know how to model it as fiber reinforced composite in comsol 4.3..thank you
06 July 2014 2,302 1 View
I 'm doing analysis on solid objects in Ansys workbench. I need to find the result for particular named nodes. I have crated a group of nodes where I need to find result using named selection, but...
04 May 2014 4,579 3 View
Is there any change in knot vectors between uniform & nonuniform Bspline? What are the equations used to calculate Knot vectors in both of these cases?
03 April 2014 9,904 1 View
I'm looking for the MATLAB code for Barlat 96 yield criteria for anisotropic aluminum alloy to determine the material constant and to plot yield surface. If you happen to have it, I'd be grateful...
02 March 2014 9,259 0 View
I have a surface generated using photogrammetry in stl format. I want to thicken it into a solid using Matlab. I need an algorithm. If anyone has worked on such problems please suggest me how to...
02 March 2014 405 2 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
I'm currently working on calculating the collision cross section (CCS) for various ions, and I'm facing challenges when dealing with sodiated and multiply charged ions. Most of the resources I’ve...
08 August 2024 8,329 0 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View
I am currently working on a project involving liposomes and need to determine the maximum volume of siRNA that can be added to a 2.5 mL liposome solution with a total lipid concentration of 10...
30 July 2024 6,420 1 View
Sure, here is the translation: I have a 3D orthogonal woven composite structure where warp, weft, and binder yarns are oriented in three directions. After modeling these yarns and the matrix in...
28 July 2024 8,169 0 View
Dear Siesta Users, I installed Siesta 5.0.1 and I want to use Grimme's D3 correction. According to the 5.0.1 manual, I could use a few parameters to include the D3 correction in the...
27 July 2024 5,748 0 View
It has been long known that EDC carbodiimide and NHS easter's half life agains hydrolysis are highly related to pH. However, very surprisingly, not yet found a paper giving a table/chart of their...
25 July 2024 8,738 0 View
I run mechanochemical reactions that involves the use of a large amount of catalyst (1:1 molar ratio to the reactant). When I try to understand the effect of amount of catalyst on the reaction, I...
23 July 2024 9,938 1 View
Hi, I am a PhD student working at Jagiellonian University, Faculty of Chemistry. My work is related to the development of new analytical methods for the quantification of short-chain fatty acids...
22 July 2024 5,492 6 View
I know that films and other low-thickness laminated products are produced using biaxial orientation, but is there something similar for sheets with a thickness of around 6 mm? Or are they...
21 July 2024 1,559 1 View