What is the reason of collapse of water tank shown in the attached you tube?

https://www.youtube.com/watch?v=WLEkC_JbTsQ

03 April 2017 1,021 2 View

No title

02 March 2017 8,545 19 View

Why do BS8007 specify the allowable crack width of water retaining structure as 0.2mm for severe or very severe exposure?

Why 0.2 mm crack width?

02 March 2017 9,166 3 View

Which type of multiple-cell box girder is better, cells connected by top flanges or cells connected both by top and bottom flanges?

How we can design box girder bridge?

02 March 2017 9,977 3 View

What is the effect of rusting on steel reinforcement?

How does rust affect on the bonding between steel bars and concret?

02 March 2017 3,267 10 View

What is the difference between working stress approach and limit state approach?

02 March 2017 415 2 View

It is not necessary to design nominal reinforcement to piles. Is it true?

Can we use same code provisions of columns for piles?

02 March 2017 7,705 3 View

In carrying out compression test for concrete, should test cubes or test cylinders be adopted?

Relation between cubes and cylinder

02 March 2017 5,645 4 View

If concrete compression test fails, should Schmidt hammer test be adopted as an alternative test to prove the concrete strength?

Non destructive tests

02 March 2017 5,232 31 View

What is the meaning of P-delta analysis?

Some codes provisions refer to this type of analysis.

02 March 2017 8,549 5 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

How Relativistic effects is one reason for lanthanide contraction?

The Lanthanide contraction which is the decrease in ionic radii of the elements in the lanthanide series from atomic number 57, lanthanum, to 71, lutetium, is due to poor shielding of the 4f...

01 March 2021 2,272 4 View

How to define and get results (stresses) for certain points of a model in abaqus, using python? When the size of the model changes?

I want to do a parameter study of a aixsymmetric cylinder in Abaqus. I want to create several jobs where I get the stresses for 3 different points in my model. These points are defined. I wrote a...

01 March 2021 10,078 1 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

Dapi fluorescence protocol for colon cell lines ?

28 February 2021 2,534 2 View

How can we simulate an hyperelastic-viscoelastic behavor with Ansys APDL?

I am working on modeling and simulation of biomecanical material behaviour, I have succeded on simulating skin using anisotropic hyperelastic material, on APDL and in our lab's finite element...

28 February 2021 552 3 View

For modelling epoxy-based matrices (in composites), which model in ABAQUS is the most suitable, Concrete damaged plasticity or Drucker-Prager model?

I am working on developing a micromechanical FE model for predicting kink-band formation in UD composites. To model matrix plasticity, which model, out of Concrete Damaged Plasticity and...

28 February 2021 5,415 1 View

How to find the right number of integration points in second order 3d finite elements?

I am familiar with finite element simulations and numerical schemes like the Gauss Legendre quadrature. I also know that the Gauss integration yields exact values for polynomials up to degree 2n-1...

27 February 2021 6,818 3 View

How relevant is Mini slump cone?

for all the rheology researchers, my question is, how relevant is a mini slump cone (smaller than a standard 50 cent rheometer). currently based on testing, the thickness of slumped material is...

26 February 2021 3,668 1 View