When such formulation contains talc, colloidal sillicon dioxide as well as magnesium stearate, even though sticking observed in lower strength with tablet weight of 75 mg where as there is no sticking in higher strength with tablet weight of 150 mg.
Hi, I am looking to link MATLAB to Aspen Adsorption. I know that for Aspen Plus, it is possible to use actxserver(). Does anyone know if the same method can be used for Aspen Adsorption as well?...
20 June 2024 8,338 2 View
There are two proteins X and Y both containing signal peptides. We want to create a fusion protein of X-Y. X will be displayed on the surface so we retained the signal peptide of X. Further, do we...
11 June 2024 6,117 1 View
the query centers on determining the most efficient and precise latest technology available in the market, capable of swiftly analyzing complex mixtures while maintaining a high level of...
26 May 2024 2,898 6 View
I am doing optical simulation for solar cell using tcad Synopsys simulator.
26 March 2024 3,785 1 View
These terms are related with earthworm.
22 February 2024 7,785 0 View
what are different turbulent inlet conditions in T-Junction pipe flows, which leads to turbulence at T-Junctions during fluid flows
30 January 2024 6,455 2 View
I have been trying to expand NK cells isolated from Healthy Donors in CTS NK Xpander Medium from Thermofisher with IL2 at 500U/mL conc. being provided. Alongside, I am pre-activating NK cells with...
29 October 2023 9,163 4 View
I am masters student, looking for thesis topics, your suggestions are required.
10 October 2023 4,645 4 View
Actually I want to know whether defrent 5 groups of facial index can answer the person's one personality like OPENNESS which has five categories very low, low, average, very high and high. Like...
25 September 2023 800 2 View
I want to model a hetero 10-mer protein with 5 unique chains. can i do it with alphafold? or if there are other tools please let know how can i do it?
11 September 2023 3,042 2 View
Please suggest me, I want to present my research work.
13 July 2024 1,461 1 View
I understand the basic definitions of creep and pressure relaxation. However, I am confused about the exact difference between them. See attached photo. Because a compression force is applied,...
17 June 2024 5,344 2 View
I have conducted uniaxial compression tests on my 3D printed samples. Since these are perforated samples, ideally they should have negative (or near zero) Poisson's ratio. However, DIC (digital...
21 May 2024 9,967 0 View
Hello ~ I'm currently beginner using Wannier90. My target molecule is "EuTiO3". The electron configuration of this molecule is as follows: Eu: 1s2 2s2 2p6 3s2 3p6 3d10 4s2 4p6 4d10 5s2 5p6...
06 May 2024 2,066 1 View
Hi everyone, I have a question that has been bothering me for a month. In Abaqus Explicit, I used shell (S4R) to simulate a compression experiment. I chose 'general contact' with 'all* with...
22 April 2024 3,975 4 View
I am trying to model a quasi-static compression of a complex structurAl geometry. The experiment was done at 2 mm/min of loading. I am using ANSYS Explicit Dynamics. I’m also using Automatic Mass...
20 April 2024 2,934 4 View
I am comparing a simple tensile stress and compressive stress results getting from Abaqus with my manual calculations. But, I could not able to find out where to check the value of tensile and...
19 April 2024 5,186 2 View
Over the decades, Researchers have been recommending that biogas should replace Natural gas as a domestic fuel source. On Sunday 14th April, 2024, the resource person at a meeting of Akwa Ibom and...
16 April 2024 6,937 0 View
While conducting experiment following data were obtained Compressor inlet pressure : 120kPa Compressor inlet temperature: 29°C Compressor outlet temp:1000kPa Compressor outlet temperature: 66°C
07 April 2024 3,045 4 View
I'm interning at a small company, and I am working on a project involving the characterization of polymer parts. our company lacks the necessary equipment for this task, and outsourcing to a...
03 April 2024 4,545 3 View