What are the best software for semiconsductor materials?

More Naima Ghoutia Sabri's questions See All

Use of NC or NTC to descibe negative control?

Hello, I would like to ask which is the best terminology to use for describing a negative control in an experiment (drug testing in-vitro, viral infection): NC (negative control) or NTC? Thank you...

18 July 2024 4,183 2 View

How can i make Microsoft Copilot have predictive capabilities ?

I am working on a project to integrate data from Campus Management Systems and Learning Management Systems into a predictive AI model that forecasts students' academic performance. I want to use...

22 June 2024 831 2 View

What is the impact of the devastating Syrian war on the environment in Syria?

Syria has been suffering from a senseless, devastating war for more than 14 years, in which the combatants did not respect any sanctity of humans, trees, animals, cities, archaeological,...

19 June 2024 8,496 3 View

What could be the possible reason of a sudden fluctuation in a stable RMSD plot of a protein-protein simulation?

I have run MD simulation of a protein-protein docked complex for 50ns. The RMSD plot obtained from the simulation is attached here. The RMSD plot shows a stable trajectory for entire simulation,...

09 June 2024 7,886 1 View

Is there any software/web server to add carbohydrate chains to a modelled protein?

Previously I have used GlyProt to add carbohydrate chains with my modelled protein, but the server is not working now. Is there any alternative tool for modeling glycosylated protein?

01 June 2024 894 1 View

Numerical modelling of liquefaction analysis in silty-sand?

in laboratory i am working on cyclic triaxial machine to research liquefaction analysis of silty-sand. finding my research i want to represent in numerically.

25 May 2024 6,480 1 View

Do military decisions achieve peace, or are peace decisions better, less expensive, and more sustainable?

I believe that the cost of establishing peace is much lower than the cost of war and is many times more sustainable, and it is possible to start from the axiom that $1 spent on economic and social...

26 February 2024 4,286 3 View

How can the green economy mechanism be used to achieve economic recovery in countries suffering from disasters (for example, Syria)?

I am working on research to use the green economy mechanism to achieve recovery of the Syrian economy. The Syrian economy has been suffering from a devastating war for more than 13 years, in...

30 January 2024 6,064 0 View

Are we on the verge of a third world war?

The increase in global tensions, especially internal conflicts that have lasted so long that they have become cross-border and threaten the region and subsequent regional and global peace. First,...

16 January 2024 451 1 View

Are we on the verge of a third world war?

The increase in global tensions, especially internal conflicts that have lasted so long that they have become cross-border and threaten the region and subsequent regional and global peace. First,...

16 January 2024 436 3 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

Is it necessary to covary exogenous constructs in a structural model?

I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...

03 August 2024 6,028 4 View

Given the current level of natural phenomena cause by the climate change and environmental pollution, will the AI find the technological solutions?

AI-driven technologies offer previously unheard-of capabilities to process enormous volumes of data, extract insightful knowledge and improve predictive models, according to the UN’s World...

31 July 2024 9,733 3 View

Mokhtar Berrahal

FP-LMTO is very good simulator device

Abdelkader BOUAZIZ

Dear all,

I suggest COMSOL (I am not an expert in manipulating it). Please feel free to tell me if you need additional information. Regards

Billel Smaani

For semiconsductor devices, Silvaco-TCAD and ISE-TCAD are the best softwars.

Kai Fauth

Unless you give more information on WHAT properties you wish to compute, it may be difficult du come forward with useful answers. "semiconductor materials" and "magnetic materials" is too broad.

Naima Ghoutia Sabri

I try to study the magnetic and electronic properties in a Duluted magnetic semiconductor .

I thank every person who answers me.