Does all mineral oil contains asphaltenes?

I had a mineral oil of 460cSt (containing sulphur and phosphorus), after addition of nanparticles (carbon nano tubes and graphene) the viscosity decreased significantly. literatures says that the...

07 August 2018 9,447 1 View

What can be the reason for high coefficient of friction and low wear scar in a lubricant containing carbon friction modifier and zinc oxide?

A lubricant contains zinc oxide nano particles and carbon FMs, the coefficiet of friction is high while the wear scar diameter is less for the samples. The load was 392N @1200rpm @75degree C.

03 April 2018 3,084 6 View

Does the coefficient of friction values depend on the type of tribometers used?

Experiments were carried out using pin on disc apparatus (120N, 800rpm, a flat faced pin 10mm, room temperature) and four ball test(120N,800rpm , AISI 52100 balls , 75 degree C). The lubricant...

11 December 2017 3,529 2 View

What is the Youngs Modulus of Zinc Oxide Nanoparticles?

Elastic modulus of Zinc Oxide nano particles

07 August 2017 7,994 2 View

How to explain the phenomenon of extreme pressure properties in case of graphene and carbon nano tube?

Graphene and carbon nano tubes shows better extreme pressure characteristics when used as additives.

06 July 2016 8,544 0 View

Can anyone tell me some applications where we use gears of hardness 22Rc-30Rc?

Specific Application please.

06 July 2016 3,358 2 View

Which is more preferable mixed lubrication regime or boundary lubrication regime?

06 July 2016 9,847 7 View

How does Young's modulus,shear modulus,Poisson ratio of a nano wire/tube/particle influence the coefficient of friction?

Mechanical properties influencing coefficnet of friction.

05 June 2016 1,316 2 View

Which roughness parameter would be more suitable to compare between steel surfaces : average roughness,skewness or kurtosis?Why?

05 June 2016 3,356 3 View

Does graphene exhibits better frictional properties than carbon nano tubes?

Graphene shows better frictional properties than carbon nano tubes.

05 June 2016 2,558 1 View

What is the production process of CaFe ferroalloys?

I looking for ferro calcium production process

03 March 2021 1,755 4 View

12% ledeburitic cold work tool steel, etched for revealing retained austenite, any help for clarifying?

Hello everyone. Given microstructure image belongs to a 12% ledeburitic cold work tool steel (annealed and tempered). The sample was etched with picral (100 mL ethanol and 4 g picric acid). I...

02 March 2021 4,119 3 View

Why Austenite grains in steel show much more twinning than ferrite grains?

It is oftentimes said to be a distinctive metallographic trait that differentiates a fully austenitic and a fully felly ferritic steel without etching that might distinguish between two. Why...

02 March 2021 728 2 View

How Can I bring as much common elements in steel as possible to calculate stable phase(s) in OpenCalphad?

As I was tweaking step-by-step OpenCalphad6 Macros step1.ocm involving phase and thermal property calculation of a High-speed steel, I could not incorporate more than 6 elements in the steel...

01 March 2021 8,840 1 View

I need to accelerate corrosion in steel parts that are used in a salt-water environment. Is there a technique for doing so?

I have a structure that employs d-ring swiveling tie-downs that corrode during use and become "frozen". I have sample swivel assemblies that I wish to corrode to see if I can free them using one...

01 March 2021 3,739 3 View

Why is my platinum counter electrode getting dirty during electrodeposition?

I am conducting anodic electrodeposition of MnO2 onto a stainless steel substrate, using a platinum strip as a counter electrode. This is done galvanostatically, with the current held between 5...

27 February 2021 1,829 3 View

What kind of steel moulds are used for hot pressing metal powders?

My main concern is that the metal powders should not weld to the mold surface and I should easily be able to eject out the pressed samples. I am looking for alternative for graphite moulds. The...

22 February 2021 2,965 4 View

What are effects of steel jacketing on flexural strength?

Dear all, If steel jacketing is used to retrofit a reinforced-concrete (RC) column, can we use it to improve flexural strength? I understand that we leave gaps between the ends of the jacket and...

22 February 2021 1,906 5 View

How to model steel jackets using SeismoStruct?

Hi all, Does SeismoStruct support modeling rectangular RC columns retrofitted with steel jackets (e.g. rectangular, elliptical) ? Any suggestions for other software (apart from...

20 February 2021 4,521 1 View

Thermal and mechanical properties of concrete and steel after cooling?

How do the thermal conductivity, specific heat capacity, plastic strain, critical compressive displacement, and thermal expansion of both hot-rolled steel and concrete change after cooling based...

15 February 2021 1,385 5 View