Errors in DNA sequences?

I am trying to better understand the scope of DNA replication and sequencing errors, e.g. 1. I have seen similar error rates of 10e4 to 10e5 for cell & instrumental DNA replication,...

24 February 2021 4,397 3 View

Can I perform Zeta-potential analysis with for nanoparticles dispersed in propylene glycol using disposable capillary cell (DST1070) ?

I am conducting a zeta-potential experiment but it shows I have a poor quality result and my sample conductivity is low. My sample is copper nanoparticles dispersed in propylene glycol.

05 December 2020 3,966 9 View

No title

02 July 2020 1,966 6 View

Please help; How can I address ontological, epistemological, axiological issues in my research?

I am studying an application of Competence Based Training by teachers. I want to know how they apply it in classrooms, if they have any Pedagogy Content Knowledge (PCK) deficiency in using such a...

05 May 2020 1,039 15 View

Why is my antenna showing an impedance of 106.6 Ohms on the smith chart instead of 50 Ohms?

Hello everyone, I'm having difficulty with the line input impedance of a patch antenna signal. It's showing s1,1 impedance of 117 ohms on the smith chart but the correct impedance should be 50...

16 March 2020 6,552 3 View

Is there a statistical distribution to model the sum of independent squared Gaussian random variables with different means and variances?

The sum of squared zero-mean Gaussian random variables with different variances can be modeled by a generalized Chi-square distribution. However, I am looking for the PDF of the sum of squared...

06 January 2020 2,001 6 View

What mathematical function or formulae can enable me superimpose multiple curves (up to 25 ) on one another?

I wish to shift multiple lines or curves (up to 25 lines/curves) so that they are superimposed on one another. This is to enable me see clearly the points or regions where any one of the curves...

25 November 2019 6,530 4 View

Binary online matrix calculator?

Please could someone assist with sites of an online matrix binary calculator

19 November 2019 5,522 3 View

How to model a hyperelastic plate in ansy apdl?

I am modelling an elastomeric bearing in ansys apdl but the elastomer does not bulge under compressive load as it should. it "splashes out" under any significant loading. is it the loading problem...

26 June 2019 2,003 3 View

What is a good measure of surface roughness (i.e. topographic complexity) that can be derived from a DEM?

I want to generate an environmental layer depicting topographic roughness, or complexity, scores using a DEM in ArcMap. I know there are lots of available methods (i.e....

09 April 2019 6,563 4 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View

Can we classify HV and LV lines based on line length?

I have dataset which shows the length of power lines. I need to classify the lines based on the line length. Is there a rule to classify the High voltage (HV) and low voltage (LV) lines based on...

03 March 2021 4,116 4 View

What is the production process of CaFe ferroalloys?

I looking for ferro calcium production process

03 March 2021 1,755 4 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Research on Supply Chain Management in Indian context?

Hi, I am planning to apply for the PhD degree in the Supply Chain Mgt. with specific area of "Cold Storage warehouses" during Pandemics and wars. Where lock downs and shut downs are frequent....

02 March 2021 285 2 View