Under de-aerated conditions, what is the best technique to follow cathodic delamination?

01 January 1970 0 3K Report

It is a simulation of an underwater pipeline, where there is a low concentration of oxygen, and I try to follow cathodic delamination of epoxy coated steel with thickness 700 micrometer.

Badges
Science topic

More Mohamed Gobara's questions See All

What is the software or technique to predict the structure of new MOF other than SC-XRD?

We begin a new research related to MOF (powder) and we need to predict its molecular structure. We have powder-XRD and atomic ratio from EDX and XRF, but we do not have Single Crystal-XRD...

10 November 2018 6,607 5 View

What are the differences between ECN and ZRA techniques for corrosion measurement?

01 January 1970 5,161 4 View

What is the best technique to follow the cathodic delamination of very thick coating (+700 micrometer)?

The metal is pipeline steel (X70) and the coating matrix is epoxy. I need to follow the delamination during applied cathodic potential. The solution is NS4.

01 January 1970 1,531 7 View

What is the production process of CaFe ferroalloys?

I looking for ferro calcium production process

03 March 2021 1,755 4 View

12% ledeburitic cold work tool steel, etched for revealing retained austenite, any help for clarifying?

Hello everyone. Given microstructure image belongs to a 12% ledeburitic cold work tool steel (annealed and tempered). The sample was etched with picral (100 mL ethanol and 4 g picric acid). I...

02 March 2021 4,119 3 View

Why Austenite grains in steel show much more twinning than ferrite grains?

It is oftentimes said to be a distinctive metallographic trait that differentiates a fully austenitic and a fully felly ferritic steel without etching that might distinguish between two. Why...

02 March 2021 728 2 View

Adherance of Polyaniline coating over stainless steel?

Is the electropolymerisation of polyaniline coating over stainless steel (SS) via Cyclic voltammetry technique is really adherant? Else how to improve the adhesion of the coating, whether any...

01 March 2021 8,220 2 View

How Can I bring as much common elements in steel as possible to calculate stable phase(s) in OpenCalphad?

As I was tweaking step-by-step OpenCalphad6 Macros step1.ocm involving phase and thermal property calculation of a High-speed steel, I could not incorporate more than 6 elements in the steel...

01 March 2021 8,840 1 View

I need to accelerate corrosion in steel parts that are used in a salt-water environment. Is there a technique for doing so?

I have a structure that employs d-ring swiveling tie-downs that corrode during use and become "frozen". I have sample swivel assemblies that I wish to corrode to see if I can free them using one...

01 March 2021 3,739 3 View

Which fluorescent dye to use for measuring total ROS production?

Is DCFDA appropriate for measuring total ROS production, or can it only detect certain types of ROS? If I want to measure total ROS production, which dye should I use?

01 March 2021 9,447 3 View

Is there a method of determining feed digestibility without the need to re-pellet the feed?

I am aiming to determine the ADC values of a commercial fish feed, but I do not have a steam pelleter or extruder available to me. Ideally, the pellets could be coated with some inert marker....

28 February 2021 7,967 3 View

How to immerse bricks in wax ( for coating ) ?

Do we immerse the bricks horizontally or vertically ? #bricks#waterproofingsurface#civil#engeenering#chemicalengineering#wax#parafinwax

28 February 2021 6,685 2 View

For gelatin coating for culturing HUVEC.Should the gelatin be made in sterile water or PBS? Do I need to autoclave the gelatin soln after making it ?

I want to use 0.1% gelatin. Should that be made in PBS or sterile water? Should I autoclave the gelatin soln after making it in water/PBS?

28 February 2021 274 2 View