Turbulent energy spectrum graph in OpenFOAM?

M D Dinesh Muthamil Raja @M-D-Dinesh-Muthamil-Raja

25 May 2022 0 7K Report

Can anybody give a sample file for extracting turbulent energy spectrum from LES simulation in OpenFOAM. I am struggling to get it.

Thanks in advance.

Badges
Science topic

Similar topics
Filing

More M D Dinesh Muthamil Raja's questions See All

Is there any cases algae not using the nutrient from the wastewater and grow normally?

I am working on microalgae cultivation using waste water. The initial concentration of nutrients were less but the microalgae has achieved biomass growth of 2 g/L. The final concentration of...

08 August 2024 4,812 2 View

Where to start the Analytical model for Dry sliding wear of metal surface ?

I am doing research on wear mechanism of the additive manufactured metal parts under dry condition. Please share the reference to start the analytical modelling of the wear prediction.

29 July 2024 6,115 0 View

While doing Chronoamperometry, when the light is turned off, why the current is not decreasing sharply?

Here, I have used Ag/AgCl as reference electrode and 0.5M KOH.

29 July 2024 4,538 3 View

Is it possible to dock more than one drug in the same active site or pocket of a protein to study synergistic/antagonistic/additive properties?

I wanted to know whether we can observe the synergistic/antagonistic/additive properties of combinations or mixtures of compounds through docking analysis. But during docking preparation any...

28 July 2024 7,413 6 View

I have calcined my catalysts without flowing air from the compressed air cylinder will there be any problem with my reaction if i use that catalysts?

FYI Catalyst is MFI zeolite Si/Al = 140,25.40.11.5,15 I am using this catalyst to study methanol to DME conversion

25 July 2024 2,486 2 View

How can I measure arsenic concentration in a patient blood?

I intend to get an economical and accurate LAB TEST to measure arsenic concentration in blood sample.

23 July 2024 3,654 2 View

It is possible to conduct a structured written interview for a qualitative study?

In your opinion, I would like to know if a qualitative study with a structured interview can be conducted in writing. In other words, we sent out open questions and asked the interviewees to...

11 July 2024 4,163 4 View

What is Differential-Fed in microstrip patch ant? How it is design in CST studio? What is process and procedure to do Differential-Fed in CST studio?

What is Differential-Fed in microstrip patch antenna ? How it is design in CST studio? What is simulation process and procedure to do Differential-Fed in CST studio ?

08 July 2024 7,464 1 View

Validated HPLC method for the estimation of the Amphotericin B ?

During the release test of Amphotericin B using 1% Tween 80, i observed three peaks even in the standard. The first peak consistently yielded results around 500%, while the other peaks showed...

08 July 2024 1,330 0 View

How to know the TM/TE modes in antenna design in CST studio?

How to know the TM/TE modes in antenna design in CST studio? Example: TM01 ,TM02 ,TM10, TM12, TM30 like this... how can identify the antenna is operate the above said mode? can any one explain...

08 July 2024 6,609 2 View

Reversed flow at outlet due to the release of DFBI?

Hi everyone, I am working on a simulation involving restricted canal with ship using DFBI. I am facing reversed flow in my outlet boundaries as the DFBI is released (In 1.25s). Is there any...

17 July 2024 7,032 1 View

Why does the static pressure at the outlet become a very negative value when the outlet flow boundary conditions are used?

The simulation is for turbulent and incompressible flow and the inlet velocity condition is selected for the inlet

12 June 2024 3,568 2 View

Is there a way for OpenFOAM to calculate the grid resolution (delta x+, delta y+, and delta z+)?

Hi everyone, is there a easy way for OpenFOAM to calculate the grid resolution (delta x+, delta y+, and delta z+)?

12 June 2024 9,459 1 View

How to analyze a speaker box with Comsol?

Airflow Turbulence Air Dynamics Signal effect frequency response

02 June 2024 2,986 1 View

Residuals are getting converged, but at a very migh magnitude of values. Why??

I am running a coarse DNS case for pipe flow with 2.1 Million cells. My residuals are quite fluctuating as its a fully turbulent annular pipe flow case but its getting statistically converged to a...

29 May 2024 2,063 5 View

Effect of \nu variation for a turbulent pipe flow at a constat Reynolds number ???

I am trying to run a turbulent pipe flow simulation with turbulent Reynolds number of 600, for 15 seconds, the flow is pressure driven due to gravity enforced buoyancy force which gives kinematic...

20 May 2024 5,619 3 View

How to fix " turbulent viscosity limited to viscosity ratio of 1.000000e+05 in xxx cells" ?

Hi everyone, I try to do a simulation about heat transfer of supercritical hydrogen in a cooling channel. Properties of H2 is obtained from NIST and displayed by an UDF function. I used the k-w...

16 May 2024 4,076 2 View

Why <u'v'> cross-corelation is important whilte studying Reynolds Stresses in most studies??

In most common turbulence model studies, when considering Reynolds stresses the components of auto-correlation, , , and components of cross-correlation are considered. In the research studies...

02 May 2024 2,776 2 View

Ask help for the numerical beach in OpenFOAM, or other better wave absorption cases?

Hello everyone, I am building the 3D NWT based on our lab tank in OpenFOAM, I am using the flap wavemaker and 3Dwaveabsorption in olaFLow currently. The generation is accurate and perfect....

22 April 2024 8,427 0 View

What is the shape of a 2D profile in external flow that is optimised for maximum heat transfer from the profile to the fluid?

I found this article: Investigation on flow and heat transfer characteristics in r... that claims circular profiles are better for heat transfer than streamlined profiles as they induce more...

17 April 2024 6,066 1 View