Tool selection for composite material, say SIC Al2o3 as a workpiece, was difficult. Can anyone suggest the right tool for friction stir welding?

More Venu Jaiganesh's questions See All

Can we combine a case reports/case series with case control studies for doing systematic reviews?

If we can do, please suggest an example of one such article. Thank you

23 April 2023 9,620 4 View

Cumulative fraction of dose excreted unchanged in urine over the entire collection interval (Fe) and Renal Clearance (CLr)?

Dear Research, The values of Fe and CLr values are decreasing while the dose is increasing in a pharmacokinetic study. May I know the clarifications on this? Regards, Venu

29 March 2023 9,705 0 View

Is there a scale to measure commitment to one's goals?

Is there a brief 5-6 question scale to measure Individuals commitment to their own goals [[Career, Health goals etc.,]

28 January 2023 2,429 2 View

Satellite Animals in Pre-Clinical Research?

Dear Research Team, I would like to know the meaning of satellite animals in pre-clinical trial with respect to sampling techniques? Thank you, Venu

10 November 2022 1,679 0 View

Is it good enough to use ''Impact of Event Scale revised (IES-R)'' scale to the 2018 flood affected victims in 2020?

If I am going to use the IES-R scale for 2018 flood-affected individuals in 2020, whether can I get valid results (I am not talking about it's validity here). Because I am measuring the impact...

27 February 2020 7,175 3 View

Non-normal distribution data not normally distributing after transformation. Any Suggestions?

Hi, I have a data set I am working on. The data is not normally distributed (Image 5). I tried to transform with log transformation and Square root transformation; both of them did not work—any...

27 February 2020 9,396 8 View

Can I use General Health Questionnaire (GHQ-12) to study psychological distress among flood affected individuals in 2018?

I would like to asses the psychological distress among August 2018 flood-affected individuals. Can I use GHQ-12 in 2020?. Because there is a time gap of 1 and half years after the floods, does it...

23 February 2020 9,886 3 View

Merging data is SPSS by variable?

I have two data sets A and B. Set A has 6000 cases but has interested variable V1. Set B has a variable V2. The cases are generic in set B (so cannot merge with Set A by case). I want to add V2...

31 January 2020 8,544 3 View

How far (Kms) that the Salt water intrusion takes place from the sea (Underground) towards the main land?

Suppose If I want to dig a well say near to the Arabian Coast (India), How far from Sea that I have to dig a well in order to avoid the salt water intrusion through coastal aquifers. I would like...

23 May 2019 2,994 1 View

Can we assume following for multi path clutter suppression?

Dear Tamas Peto, Can we assume that same clutters are received by the passive radar in several sequence of CPIs.(or at least in limited number of continuous CPIs). I mean if we have 4 clutters...

07 January 2019 5,842 0 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

What should a Mechanical Engineering PhD scholar focus on during their PhD to enhance their chances of securing a postdoctoral position?

29 July 2024 7,714 4 View

May I know the exact Quartile of the journal- Advanced Engineering Materials (Wiley) for material science category?

In some data sources it has been grouped in Q1 and some shows it is Q2.

29 July 2024 4,227 2 View

Ternary in Electrical Engineering?

Dear Research Community I would like to invite Elctrical Engineering specialists to solve problems related to Ternary Algebra or tripple sets I have an algorithm that places in relation three...

28 July 2024 5,771 2 View

What topic or subject does Production Engineering need to address more?

Contemporary scores or innovations in scientific approaches. Hybrid methodologies, emerging themes and cross-cutting issues?

27 July 2024 648 3 View

How should operational parameters be selected when developing a pore-free laser welding technology?

There are three operating parameters - the laser power, the diameter of the focus spot and the scanning speed. It is necessary to obtain a seam of a given depth without pores. What parameter...

27 July 2024 7,168 2 View

Can a shoot-through event of a tri-state digital buffer cause momentary Hi-Z state?

// interested in the difference between floating events and short circuits.

22 July 2024 6,565 0 View

Is there a good macro photography kit for on-site metallurgical investigation?

I am looking to purchase a photography kit for onsite metallurgical investigations, such as capturing photos of worn areas, hot tears, cold tears etc. Could anyone suggest me a good...

22 July 2024 3,490 2 View

Why do fish have fishy odors naturally ?

Chemical Engineering /Food Engineering

20 July 2024 4,152 4 View

Masonry Interaction Module ABAQUS?

I am simulating interlocking / dry stacked masonry in Abaqus. I am using a friction coefficient of 0.6 for my model as it is stated in the previous research as well as in the base paper. The...

16 July 2024 5,047 0 View

René Schürer

You can weld with typical tool materials, which are used for steel, titanium and similar "high abrasives". e.g. W-Re, W-LaO or PCBN tools

A.P. Reynolds

I am assuming that you are welding Aluminum matrix discontinuous composites (it is not completely clear from your question). If that is true, a good, relatively low cost alternative tool material is Ferro-TiC: http://www.ferro-tic.com