To determine the threshold value for intervention?

04 April 2018 0 3K Report

I am modelling a case of intervention. How do I obtain the threshold value or the point of intervention when the point is not too obvious?

Badges
Science topic

Similar topics
Engineering
Modeling

More Ette Etuk's questions See All

Contradictory results from minitab?

I used minitab to compare two means from samples of size 400 each. Firstly minitab gave a degree of Freedom of 358 rather than n1+n2-2=798. Moreover its computed mean difference fell into the 95%...

05 June 2018 8,293 4 View

How do I obtain expected frequencies under the hypothesis of negative binomial fit?

I am trying to model the number a goals scored by the teams of a soccer tournament at group stage. The tournament involves eight groups of four teams each. This means that each group involves 6...

06 July 2017 6,676 4 View

Is it correct to test the significance of a cham\nge in the mean of a time series based on t-test which is based on assumption of data independence?

I am asking this question because time series data, rather than being independent, are correlated.

01 January 1970 1,670 6 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

Is it necessary to covary exogenous constructs in a structural model?

I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...

03 August 2024 6,028 4 View

Given the current level of natural phenomena cause by the climate change and environmental pollution, will the AI find the technological solutions?

AI-driven technologies offer previously unheard-of capabilities to process enormous volumes of data, extract insightful knowledge and improve predictive models, according to the UN’s World...

31 July 2024 9,733 3 View