Why does flow deformation occur at the test line and control line on nitrocellulose membranes (LFIA)?

I use 1% BSA in 10 mM phosphate buffer (pH 7.4) solution when striping my nitrocellulose membranes with antigens and antibodies. However, I always observe deformed flow when my sample or running...

16 February 2021 4,224 3 View

How can I set up UV irradiation for crosslinking lab?

Hi, I am using a mix of 2 polymers and want to try and crosslink them. I have a UVA lamp of 365nm and have tried the lab previously at 30cm above. How would you recommend I approach the lab and...

31 January 2021 8,711 3 View

Which air pollution/air quality books do you recommend for working with environmental engineering students?

I am exploring up-to-date books on air pollution and air quality, and I would like to know which books do you recommend for environmental engineering students.

25 January 2021 3,972 7 View

How to simulate Sloshing water using Dynamic mesh in ANSYS Fluent ?

I am trying to model sloshing water in a tank in ANSYS Fluent using Wall motion. BUT it seems that System coupling is not responding to wall motion and it works only with Dynamic mesh.

20 January 2021 2,963 3 View

Are there other models that meet the same purpose?

Both Jakes and Gaussian models are used to characterize the power spectral densities of mobile communication channels.

11 January 2021 759 3 View

SDAS, secondary dendritic arms space relation with solidification rate?

Want to know the relation between sdas and solidification rate, the mechanism by which getting smaller space between secondary arms by increasing the rate ?

23 December 2020 735 2 View

Shall i use the country's CPI score or rank while entering the data ?

I have the Corruption perception index as a control variable in my study and i'm not sure what i have use the score or the rank of the country ? please advice what i have to use in the data entry...

09 December 2020 3,797 2 View

Any thoughts for a research topic in a master's level thesis regarding combination of Supply chain and entrepreneurship?

Hi, we are two master's students at JIBS and currently looking for inspiration and suggestions for a research topic that has a connection of both "supply chain" and "entrepreneurship". maybe...

18 November 2020 2,524 3 View

Can electrophoretic mobility measurements of polymer-coated AuNPs be used to infer the role of charge (if any) in their dispersion stability?

Hello Everyone, We have stable citrate-coated AuNPs dispersed in water. Different polymeric protective coatings (PEG, PVP, BSA) have been chemically grafted to the citrate-coated AuNPs for...

17 November 2020 2,903 16 View

How can instructors assess the intercultural competence of their ESL students?

Intercultural competence is a skill rarely taught and measured in ESL venues. What is an ideal way of measuring the student's progress in developing intercultrual awareness and testing it?

08 November 2020 2,176 16 View

Why almost every element would be metallized in sufficiently high pressure and low temperature?

(This statement is from wikipedia, BTW). What is so special about metallic bond that is limiting high-P low-T state of a matter (as long as individual atoms exist, not white dwarf of neutron star...

02 March 2021 3,309 2 View

How Can I bring as much common elements in steel as possible to calculate stable phase(s) in OpenCalphad?

As I was tweaking step-by-step OpenCalphad6 Macros step1.ocm involving phase and thermal property calculation of a High-speed steel, I could not incorporate more than 6 elements in the steel...

01 March 2021 8,840 1 View

What is the error of the Txy diagram?

Hi, I know the attached Txy diagram has an error but can't figure it out. Could you please look at the diagrams and explain it to me?

23 February 2021 4,239 1 View

How the values of errors can be calculated for thermodynamic data?

I have calculated thermodynamic parameters for surfactant solutions in aqueous and mixed alcoholic solvents. I want to calculate the value of errors in the data and represent it in the table along...

22 February 2021 239 2 View

Is it possible to calculate entalphy of LiBr/H2O or another solution if we know correlation of specific heat without using any software?

Is it possible to calculate entalphy of LiBr/H2O or another solution if we know correlation of specific heat without using any software?

17 January 2021 5,522 3 View

How can I get oil properties in 300-30000K temperature range?

I need thermophysical and electrical oil properties to investigation of DC discharge in oil. Are multicomponent mixture models effective and precise in such calculations? If yes, what MC-modells...

04 January 2021 9,080 8 View

Can anyone help to get ansys-fluent tutorial zip files ?

I need the following tutorial zip files to learn the basics of the software: Using sliding and dynamic meshes Modeling solidification Using the Eulerian Granular Multiphase Model with heat...

03 January 2021 5,571 5 View

The > 91 Years long collective IQ Blunder ?

Never before was there a bigger blemish. Namely: Not to collectively underastand Zwicky's discovery of Cryodynamics, as his sister to deterministic Thermodynamics came to be called later. Dec....

30 December 2020 8,300 5 View

How to rectify the miscomputation of Pressure and Continuity in HVAC CFD Simulation Using OpenFOAM?

I'm using OpenFOAM to run a CFD study of thermal comfort within a hall. I'm using OpenFOAM v1912 and BouyantBoussinesq(Simple&Pimple)Foam solver. eI have 6 inlets and outlets each with specific...

21 December 2020 1,303 3 View

The saturation point does not reach in my ITC. Does this indicate that the interaction is weak or there is no interaction?

21 December 2020 9,407 8 View