There are many papers in SWAT. What is main reason that people are using SWAT than HecHMS in hydrological modelling?

More Santosh Kaini's questions See All

How to estimate the wilting point of a soil sample in a laboratory?

Can you please suggest different methods to find the wilting point of a soil sample in laboratory?

02 March 2017 362 11 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

What is the reason for current dropping in OER , LSV curve?

I tried four trials of the same Copper Phosphides sample in Alkaline medium ( 0.5M KOH) with Hg/HgO reference electrode and Pt as counter electrode. I used 0.001 V/s scan rate for first three...

10 August 2024 3,629 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

What may be the reasons for failures of Tube toi Tube Sheet Joints in Boiler Drum ?

We have observed that tube to tube sheet joint leaked in our boiler and needs to overcome same by knowing the root cause.

08 August 2024 3,161 0 View

How to generate a citation of my paper from ResearchGate?

How we can cite the papers from ResearchGate. I am trying to create citations for this article, Quantum Machine Learning Algorithms for Optimization Problems: Theory, Implementation, and...

08 August 2024 6,690 3 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Is there anyone with experience in TEM analysis who can assist with a manuscript for an upcoming journal?

Hello dear colleagues, We have prepared a manuscript on NiTi-based alloys and are seeking a second opinion on our current TEM results. If you are a Ph.D. holder with experience in TEM and have...

07 August 2024 9,563 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Sigit Sutikno

Hi Kaini,

In case of Rainfall-Run off modeling, both model basically almost same. Why people prefer SWAT for modeling, It is because, in SWAT we can find more feature that can not be found in HEC-HMS, for example : modeling water quality, sediment, nutrient of pesticide in agriculture field, and many more. The Rainfall-Run of modeling can support this kind of study.

Good luck

Sigit

Santosh Kaini

Which one is better to see climate change impacts on runoff pattern? Why? any papers on which one is better to see climate change impacts?