The loadflow of IEEE 5 bus system?

11 November 2018 1 4K Report

The data has been given. I have done the simulation in Simulink. Now i want to use relaying logic for the fault at any Load bus say bus 4. but i am unable to find the load current. Can anyone help me with the load flow analysis of system? No internal impedance of generator is given so i considered to have 0.15 pu of reactance.

Pouriya Boostani

I think the load flow analysis doesn't provide current information. It's all about voltage, power angle (delta), active and reactive power.

Badges
Science topic

More Tushar Mahalle's questions See All

What will be the specifications of Analog Low pass filter for 50/60 Hz signal in Simulink?

I want to design an Analog Lowpass Filter for 50/60 Hz signal in Simulink. Which block should be preferred? How to find out Passband Edge Frequency, Stopband Edge Frequency, Passband and Stopband...

11 December 2018 5,852 5 View

Is it malfunctioning of MATLAB Simulink Three-phase Circuit Breaker block?

I have simulated two three phase systems employing Three-phase Circuit Breaker Block in MATLAB Simulink. In both systems when there is fault, circuit breaker is opened. But the interruption of all...

11 December 2018 7,763 0 View

How to obtain delay?

I am simulating a model in MATLAB SIMULINK. One of the output signals varies between 0 and 1. I want to apply this output to some next block but the condition is that if output is 0 then introduce...

10 November 2018 9,546 6 View

How to compare two groups with only two measurements?

Hiiiii everyone! I have an enquiry on statistical analysis. I was looking for many forum and it's still cannot solve my problem. I want to compare means of two groups of data but only with two...

03 March 2021 8,796 3 View

Can we classify HV and LV lines based on line length?

I have dataset which shows the length of power lines. I need to classify the lines based on the line length. Is there a rule to classify the High voltage (HV) and low voltage (LV) lines based on...

03 March 2021 4,116 4 View

Enhanced Yellow Fluorescent Protein (Aequorea victoria) DNA sequence?

I am on the lookout for the Enhanced Yellow Fluorescent Protein (Aequorea victoria) DNA sequence. Does anyone know where I can find it? Thank you in advance

03 March 2021 3,568 1 View

What kind of fluid could I use for a pitfall trap that also does not invalidate molecular testing?

Hi, I want to start testing pitfall trap to obtain ants samples, but I need to conduct molecular analysis on those insects. So, what kind of fluid can I use? Ethanol expires too early and I need...

03 March 2021 5,978 5 View

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10?

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10? Since, the growth curve from day 2 to 10 won't be like the "Logistic curve" it might not follow logistic...

03 March 2021 1,401 3 View

Irradiation data for JAPAN?

Hi, Could you help me to get the latest (2019, 2020) solar resource data for a particular site in JAPAN? PV GIS and NSRDB data are not in reach to JAPAN, I'm looking for some other database for...

03 March 2021 961 3 View

Do we need to write protocol for a second study of a systematic review that has been registered and published?

I have conducted and published a systematic review and meta-analysis research with the topic related to public health and health pomotion (protocol was registed in PROSPERO). Now we want to...

03 March 2021 8,920 3 View

How to increase a model accuracy ?

dear community, my model is based feature extraction from non stationary signals using discrete Wavelet Transform and then using statistical features then machine learning classifiers in order to...

03 March 2021 6,994 5 View

Do I need to do linear regression before running mediation analysis using PROCESS MACRO by Hayes ?

I just wanted to check if I need to run a linear regression separately if I am using PROCESS MACRO to run mediation analysis. Thank you.

02 March 2021 4,359 3 View

Sample dilution for quantitative analysis using ELISA?

If the detection range is in ng/ml but the reference range is in ug/ml for a molecule or protein in serum or plasma .how to dilute and what is the initial volume to be taken for quantitative analysis

02 March 2021 7,670 3 View