What will be the specifications of Analog Low pass filter for 50/60 Hz signal in Simulink?

More Tushar Mahalle's questions See All

Is it malfunctioning of MATLAB Simulink Three-phase Circuit Breaker block?

I have simulated two three phase systems employing Three-phase Circuit Breaker Block in MATLAB Simulink. In both systems when there is fault, circuit breaker is opened. But the interruption of all...

11 December 2018 7,763 0 View

How to obtain delay?

I am simulating a model in MATLAB SIMULINK. One of the output signals varies between 0 and 1. I want to apply this output to some next block but the condition is that if output is 0 then introduce...

10 November 2018 9,546 6 View

The loadflow of IEEE 5 bus system?

The data has been given. I have done the simulation in Simulink. Now i want to use relaying logic for the fault at any Load bus say bus 4. but i am unable to find the load current. Can anyone help...

10 November 2018 3,591 1 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

What are the values needed for gabor filter's parameter for cifar10 data?

Hi, I implemented a code to gabor filter cifar10 data but the images after being filtered and stacked are not clear like the original images. I think the problem is in the way I am using the...

03 March 2021 6,317 1 View

Arena simulation - how do i model the following model in ARENA (see description) (new to ARENA)?

Hello, I'm fairly new to ARENA and I have the following problem: I have two queues in which, in each queue, a different order type arrives (both having an arrival rate of exponential 10). Order...

02 March 2021 2,431 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

How to calculate Total Flavonoid?

I analyzed flavonoid total spectrophotometry, the procedure as below: 2 ml supernatan added 5 ml dd.H2O, then added 0,15 ml NaNO2 5%, 5 minutes later added 0,15 ml AlCl3 10%, After 6 minutes,...

01 March 2021 6,722 1 View

Why the results when using wall thickness and when using shell conduction are different in ansys fluent?

Actually, I am running cfd simulation for a heat exchanger which has two fluids one hot and other one is cold fluid. there is a solid domain between them, which I removed and instead I have used...

01 March 2021 9,537 2 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

Benhaoua Mohammed Kamel

Following...

Ziad Sobih

Please read my book (The American University Laboratories For Electrical Engineering Part 1)

It has the theory and the experiment on this.

Ammar A. Oglat

Following

U. Dreher

Do I get it right? You want to eliminate 50/60 Hz "noise" from a signal that's lower than these 50/60 Hz? (Otherwise a low pass isn't the filter required.)

Aparna Sathya Murthy

May be a notch !!!

Or may be use s domain filter