Tension stiffening tests data of corroded reinforced concrete?

27 December 2021 0 1K Report

Dear all

I am looking for information of tension stiffening tests of reinforced concrete elements with corroded reinforcements. I found an article (DOI: 10.1007/s40069-016-0152-9) in this area but it is not sufficient and also reliable.

I would be happy to help me with some results of tension stiffening test of corroded reinforced concrete.

Best regards.

Badges
Science topic

More Masoud Hasanzade's questions See All

I am planning to publish a book on Springer. Can you provide guidance on how to create a book proposal?

Additionally, I welcome any general advice and suggestions you may have.

11 May 2024 5,419 1 View

What are the key and important parameters in the design of switches based on photonic crystal?

What are the key and important parameters in the design of switches based on photonic crystal? How can we have an ideal switch?

09 May 2024 7,074 2 View

What is the effect of refractive index changes on the output wavelength of all-optical sensors?

30 April 2024 540 1 View

Is it possible to achieve a high quality factor in the structure of the rings created in the crystal photonic substrate?

In the structures of combined rings, it is difficult to have completely symmetrical rings due to the delay in response time. Also, it is very difficult to reach a quality factor above 5000 in...

23 February 2024 1,222 4 View

What is industrial applications of SPD processes?

Dear researchers, as you know, the subject of severe plastic deformation (SPD) methods (ECAP, TT, HPT, ARB and so on) or ultrafine grained metals has been researched on for over 20 years. But I...

16 February 2024 1,096 3 View

Are You an Expert in Plant Abiotic Stress Response? Interested in Collaborating on Paper Writing?

I have been recently working on abiotic stresses (drought, high temperature, salinity and cold) responses in wheat (Triticum aestivum) using meta-analysis of transcriptomics (microarray) data. The...

04 February 2024 1,751 1 View

Single-chain fragment antibody (scFv) expression and purification? E. coli?

Hi all, I possess several scFv DNA sequences and aim to generate soluble forms of these single-chain antibodies to assess their biochemical characteristics, such as binding affinity and...

18 December 2023 2,070 0 View

Hydration process of soft contact lenses ?

we produce soft contact lenses with cast molding method , the material is SiHy , I need to know more about the hydration process, type of water , temperature and time we use of water bath . BR...

15 December 2023 1,656 0 View

interpertation XRD peaks after doping (LDH) layered double hydroxides?

how can i interpert XRD peaks after doping LDH. pure sample matched with JCPDF file as in papers, but after doping newly peaks appear and peaks disappear?

06 November 2023 2,674 2 View

I want to prepare a cationic liposome with Phosphatidylcholine, cholesterol and stearylamine for mRNA transfer, is it possible?

Because these lipids are cheap and it is possible for me to get them

28 August 2023 7,742 0 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

What are the limitations and challenges of using machine learning for predicting concrete compressive strength in practical applications?

Machine learning (ML) has shown great potential in predicting the compressive strength of concrete, an important property for structural engineering. However, its practical application comes with...

03 August 2024 2,546 2 View

What is the right voltage sweep direction for characterization of HER kinetics?

In general, when performing a Tafel analysis for corrosion resistance measurements, a line voltage scan is performed from say -250 to +250 mV vs. OCV at low scan speed around 0.125 mV/s. However,...

25 July 2024 7,982 3 View

Is there a good macro photography kit for on-site metallurgical investigation?

I am looking to purchase a photography kit for onsite metallurgical investigations, such as capturing photos of worn areas, hot tears, cold tears etc. Could anyone suggest me a good...

22 July 2024 3,490 2 View

Sample size for qualitative study?

I am working on scale development in behavioral finance by undertaking a mixed-method approach using the exploratory sequential design. The phenomenon has diverse meanings in existing literature...

20 July 2024 9,153 11 View

Collaboration on corrosion ?

Would anyone be interested in collaborating on corrosion?

07 July 2024 4,726 2 View

Zero pivot in Abaqus concrete 3D printing simulation using model change?

Recently I've been working on a simulation of concrete 3D printing, and has successfully simulated a layer-by-layer 3D printing process using model change. However, when I proceeded to try...

06 July 2024 2,130 0 View

What heavy aggregates are available for protective concrete in your country?

01 July 2024 1,625 3 View

How to calculate corrosion rate from potentiodynamic polarization test data for dissimilar welds?

we need surface area, corrosion current, equivalent weight and density of the metal involved for corrosion rate calculation in mm/year (lets say). For dissimilar metal welds, how can we measure...

30 June 2024 5,943 2 View

Poured Earth Concrete ?

What are the benefits and advantages of concrete flooring when used in parking lot floors, and what are the technical requirements and general specifications that should be considered to ensure...

29 June 2024 2,171 5 View