Who can tell me about low cost/ free fee of Scopus/Web of Science journal's publication in field of natural building material?

I would like to publish my research work which deals with assesment of thermal inertia, natural building materials in Scopus/Web of Science cited journal. My budget is up to 200$. I know that...

05 December 2018 6,980 2 View

What is the strain energy in ANSYS?

Hello, dear colegues! What is the strain energy density in ANSYS? How does it calculated in case of multilinear hardening? Does it correspond to the value obtained experimentally as an area...

22 April 2017 7,980 1 View

Which materials without hydrogen can be used for embedding of an analyzed sample for TOF-SIMS measurements?

18 February 2014 7,911 10 View

What is effective method determination of the energy levels of various defects and their type as well as the band gap of semiconductor materials (bulk and films) ?

The defects in crystals determine their electronic properties, which is very important for various applications. Optimization of those properties need information on the defect nature, their type...

23 January 2013 5,314 1 View

What is the most promising material for the development of uncooled detectors of radiation?

At present there is a strong need for high-sensitive non-cooled radiation detector materials for X- and gamma-rays suitable for biomedical and industrial applications. What is best material for...

23 January 2013 7,384 15 View

In your opinion, which methodology is the best for calculating the City Development Index (CDI) and Urban Sustainabiluty Index (USI)?

I'm looking for the best methodology for calculating the CDI and the USI.

01 January 1970 1,217 2 View

No title

I am interested to receive more detail information about the both basalt and diatoms part of your project because of my scientific and practical interests are partly related to chemical properties...

01 January 1970 6,389 3 View

How an ANN dataset is interpreted in a certain input order?

01 January 1970 5,150 2 View

Why Austenite grains in steel show much more twinning than ferrite grains?

It is oftentimes said to be a distinctive metallographic trait that differentiates a fully austenitic and a fully felly ferritic steel without etching that might distinguish between two. Why...

02 March 2021 728 2 View

How to remove fatty material from plant extract?

The resultant solid was partitioned three times with 250 ml of petroleum ether (40-60/c) to remove any fatty material and evaporated to dryness.

28 February 2021 9,464 2 View

1 nm thick MgO thin-film to be deposited on Si wafer using thermal evaporation. What will be the optimum deposition conditions?

Favourable conditions of base pressure, rate of deposition. Also, by which characterisation technique to be used to verify the thickness of the deposited film.

28 February 2021 3,640 3 View

Runs of nucleotides in Sanger sequencing?

I performed site directed mutagenesis, transformation, and then I sent out plasmids for Sanger sequencing and found out that there is extension of DNA just before the stop codon. I am not sure...

27 February 2021 547 3 View

Has anyone had luck using cell lines other than HEK 293 (such as COS1) to package lentivirus?

I am looking to package lentivirus in endothelial cells but I am opposed to using 293 cells due to personal ethics regarding the source. I have done some reading and saw that COS1, COS7, & CHO...

25 February 2021 3,030 1 View

How to replicate the well conditions of a crystal hit with 20%(w/v) isopropanol?

I had a crystal hit in a well with 0.1M HEPEs pH 7.5, 10%(w/v) PEG 4000, and 20%(w/v) isopropanol. Why is isopropanol in w/v here if it's just solvent? How do I recreate this well condition?

25 February 2021 9,761 1 View

What program can I use to caclulate dipole moment efficiently and without the need of excessive computation?

Hi, I am a third year chemistry undergrad doing my group project in which I need to predict the HPLC retention time of 20 aromatic molecules. to do this we require the chemical properties of these...

24 February 2021 1,384 3 View

How to search for crystal structure for material with atomic position labelled?

I am using the crystallographic open database and materials project to search for cif file but the exact structure is not mentioned or how can I deduce that the given structure and atomic position...

23 February 2021 6,723 2 View

How to generate AA6061 alloy or any aluminium alloy crystal in material studio?

I need to carry out molecular dynamics simulation on Aluminium alloy. For this i need the crystal structure that which could be further replicated to form a structure.

22 February 2021 1,410 1 View

How to improve the adhesion between germanium and silicon monoxide thin film layers using EBEAM evaporation?

I want to deposit multilayer coating of germanium and silicon monoxide on silicon wafer using ebeam evaporation?

21 February 2021 2,141 3 View