10 October 2018 0 840 Report

Can any one help me to give the answer for above question?

Can we change the temperature conditions for specific class of drugs?

please help

More Tarun Virmani's questions See All
How to proceed for writing a project for Funding agencies?

Please Help me to answer the full Procedure.

10 November 2018 4,404 0 View

What is the basic criteria to decide a project for pharmaceutics for PG students and PhD students ?

How to decide a research project? Please help

10 November 2018 1,760 2 View

How to Determine the Intrinsic dissolution rate of the drug?

How preformulation scientist helps in determination of the IDR?

09 October 2018 4,573 3 View

Similar questions and discussions
Is changing the medium during the experiment overestimate the results?

I am experimenting with cancer and non-cancer cells in a 12-well plate for 4 days with a seeding density 1*10^4/well, however, I noticed that the control group growth rate slows down on D3. Should...

07 August 2024 2,283 2 View

Which solvent is better to dissolve with secondary metabolites extracted from fungi?

I work on MCF7 cell cell for anticaner purpose and I wa to do drug preperation the drug ( secondary metabolites extracted from Aspergillus) My question which solvent is better with these secodary...

03 August 2024 4,725 2 View

Can i quantify a nanoparticle encapsulated in cell culture medium by hplc?

Hello, if you made a transwell assay where you incubate the cells with a nanoparticle-encapsulated drug and considering that in the oposite compartment you'll have both the free and encapsulte...

03 August 2024 2,730 1 View

How to maintain the drug concentration in cell culture study for long term?

I am working in the filed of long acting drugs with Nano formulation. I want to study the efficacy of my formulation in 2D cell cultures while this required media change on every two days. In such...

24 July 2024 8,696 0 View

How can I determine if a drug binds to a ribosome using a Cryo-EM map?

Hello, I am searching for the binding position of a drug in a ribosome, based on previous work indicating it binds there. The resolution of the ribosome-drug Cryo-EM map is around 2.5 Å. I've been...

19 July 2024 2,155 0 View

How to calculate percentage cumulative drug release?

How to calculate percentage cumulative drug release when, Total volume of dissolution media = 250ml Added formulation was equivalent to 10mg of drug Sample withdrawn = 1ml each time Sink condition...

15 July 2024 4,192 1 View

MTT assay - 6 well plate?

Hi, In the 6 well plate, when I am seeding the cells. Do I add 1ml of complete media to one of the wells for the control at this stage or do I wait unit I am treating the plates to do that? Also...

13 July 2024 9,783 1 View

How to convince decision makers to adjust the legislation to allow opening of drug consumption rooms?

In my country, there is a lot of public outcry in relation to the presence of drug injection and related behaviors in public. Hence at least the bigger cities would probably benefit from the...

08 July 2024 8,903 1 View

Is the use of microcrystalline cellulose MCC 102 in direct compression technology justified, given the low flowability of this excipient?

Hello everyone reading this topic! It is well known that microcrystalline cellulose 102 is recommended for use in direct compression technology, however, like other grades, it has poor flowability...

08 July 2024 2,807 0 View

How validate the dynamic molecualr simulation with experimental data?

I used forcite module of Material Studio software to simulate the dissolution of zinc production waste in deep eutectic solvent. UFF force field has been used for the optimization of molecules,...

02 July 2024 7,494 1 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close