Teflon coatings on textile?

11 November 2018 0 318 Report

Can teflon be coated on a non conducting substrate like textile or a polyurethabe sheet? I specifically want to know coating, not lamination.

Badges
Science topic

More Siddhant Varshney's questions See All

At what temperature does Graphene convert back to graphite in aqueous dispersion phase? One source says 70 and other 80 d celcius. Need confirmation?

Temperature at which Graphene stacks back into graphite in aqueous dispersion for drying

09 October 2017 2,413 5 View

While conducting 4 probe test on graphene pellet (0.25 mm thick), sparks were observed. What does this imply?

Arc observed at surface of graphene during conductivity test

09 October 2017 6,226 6 View

While making pellet of graphene for 4 probe measurement, will the pressure cause graphene to convert to graphite by overcoming vanderwaals forces?

graphene conversion to graphite on applied pressure

08 September 2017 5,294 3 View

Adhesion strength of coating?

How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...

10 August 2024 942 3 View

How do I conformally do PR spin coating on trench structure?

I did PR spin coating on trench structure. I used AZ P4620 PR and the thickness or PR is around 11um. The substrate is Si. And my trench structure depth is 141um(negative way). Even though I...

08 August 2024 2,298 0 View

Why do i have a weak plasma and no coating during rf sputtering?

I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.

07 August 2024 4,526 4 View

What is the reason I get 400nm nanoparticles using an extruder with 200 nm membrane for cell membrane coating?

I am trying to coat my micelles and PLGA based nanoparticles with cell membrane using an Avanti mini extruder according to literature . I use 200nm membrane but my particles end up to be 400nm And...

30 July 2024 3,294 3 View

What is the main used curing agent for epoxy based coating?

I am trying to coating metal oxide into steel substrate, for better sticking planning to utilse epoxy based, Could you please suggest suitable curing agent for the coating purpose

25 July 2024 438 3 View

How do you get pure primary macrophage cell culture?

I have been harvesting monocyte-derived macrophages from buffalo and cattle fresh whole blood using the same protocol for years and getting good macrophage cultures. Below is the protocol that I...

23 July 2024 4,074 2 View

Is it possible to manufacture polypropylene sheets using a biaxial process?

I know that films and other low-thickness laminated products are produced using biaxial orientation, but is there something similar for sheets with a thickness of around 6 mm? Or are they...

21 July 2024 1,559 1 View

Issues in coating of cathode material on Al foil, why we are not getting proper coating and results when the cathode was coated on Al-foil..?

We are trying to coat some cathode materials on Al-foil ( ex - LiFePO4 , S@CNT, etc). When we coated the Al foil with the cathode (ex - S@CNT) material , the cycling result was annoying. But the...

09 July 2024 5,123 4 View

Why NCM cathode slurry has coating problem?

I tried to make slurry for NCM cathode but there was problem in coating process. The detail of my experiment is following; The ratio between active material(NCM811), conductive additives(Super-P)...

08 July 2024 7,327 4 View

How can magnetic Biochar remove dye pollutants, is this technology beneficial?

The harmful Dye pollution from industrial processes such as textile generated how to remove with magnetic biochar ?

07 July 2024 8,118 1 View