What can I do with STXM and TXM on Li ion battery? Is there any good beginner level introductory paper or information? Thank you guys.
you can look at the papers published by my colleagues :
Article 3D analysis of a LiCoO2–Li(Ni1/3Mn1/3Co1/3)O2 Li-ion battery...
or http://pubs.rsc.org/en/content/articlehtml/2013/cc/c3cc42667j
Hi, I'm doing thin film research and am pretty new to the battery community. I want to ask several questions (All consider a CR2032 coin cell as example): 1. What's the different if I use a wave...
09 October 2017 2,027 5 View
Hi, can anyone suggest me a good book or a good review talking about fundamental electrochemistry in Li ion rechargeable batteries? Thanks.
02 March 2017 4,158 0 View
What if I directly test the fresh assembled Li ion thin film battery without finishing the forming cycle?
31 December 2016 6,716 0 View
Hi! May I get some idea about choosing a glovebox between Mbraun, VAC, and Inert? I am conducting Li ion battery related research. I want more on the real feedback after usage. Thanks.
09 October 2016 3,918 8 View
Why that so? Reason comes out of the Pole figure measurement. It shows that high Chi angle defocusing effect disappear after applying a parallel beam collimator on the diffracted beam optics side....
08 September 2016 2,104 0 View
As stated in the title. What's the difference and what application they will be for? Thank you.
08 September 2016 8,252 1 View
Got two questions: 1. How to choose the angle? Is that smaller the better? Since smaller angle will give less profile depth and it will thus avoid the information from the lower layer as much as...
04 May 2016 3,580 5 View
I’m trying to reproduce the acousto-optic coupling simulation in the paper Frequency–angular resolving LiDAR using chip-scale acousto-optic beam steering. LNOI(lithium niobate on insulator) is...
13 August 2024 9,795 0 View
I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?
11 August 2024 3,115 1 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
Require for Rietveld refinement in XRD.
08 August 2024 3,081 2 View
I'm currently working on calculating the collision cross section (CCS) for various ions, and I'm facing challenges when dealing with sodiated and multiply charged ions. Most of the resources I’ve...
08 August 2024 8,329 0 View
Hello dear colleagues, We have prepared a manuscript on NiTi-based alloys and are seeking a second opinion on our current TEM results. If you are a Ph.D. holder with experience in TEM and have...
07 August 2024 9,563 0 View
Hi! So i attempted to understand a novel protein behavior towards heat application by analyzing its secondary structure change. I subjected the protein to a thermal denaturation analysis using...
06 August 2024 1,989 3 View
During low-temperature testing, new diffraction peaks that appear could be indicative of several phenomena. In one of our tests, we observed notable new peaks around 40° and 45° in a specific...
06 August 2024 726 3 View
After immunohistochemistry of previously fixed in PFA and EtOH and then frozen 20 μm sections of zebrafish brain, DAPI staining is very weak (right) compared to the same sections stained without...
05 August 2024 9,637 2 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View