Spining blade using ansys apdl ?

More Kouider Bendine's questions See All

About coupling python with xfoil ?

Dear all, iam working on a sort of optimisation that involving python and xfoil. and for that I am doing a python Code to run xfoil in Iteration mode. the coupling is running well and iam able to...

03 November 2020 4,161 2 View

Genetic algorithm chromosome with Matlab ?

Dear all i want to create a random vector containing the coordinate xi and yi as depicted in the following fig with one condition the couple (xi,yi) isn't repeatable in the vector NQ: its ok if...

30 December 2018 3,323 11 View

Can anyone help with a Matlab code for finite element modeling of a plate with piezo patch?

Dear all Please I need a code of finite element plate with piezo patch using matlab.

26 November 2014 4,636 4 View

Can anyone advise on how to make an fgm plate with ansys?

Fgm

28 October 2013 2,391 20 View

Why back-to-back converter of the dfig have bidirectional power flow and how?

dfig based wind turbine

01 January 1970 9,264 3 View

Which is the best FEM software for Topology Optimization?

Dear Researchers, As the question indicated I try to find the best FEM software that provides a good build in Topology Optimization module with respect to the following constraints : 1-...

01 January 1970 9,608 5 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

How to code open-ended questions in SPSS?

Hello all, In SPSS I am going to code 2 open-ended questions. I have already read all the answers and I made a list of the most important categories to which I can code the answers. This question...

02 March 2021 1,757 4 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

How does Scientist/RG community evaluates a case study article and the impact of it on a researcher career?

An article that is published as a case study in the SJR listed journal. How much value is added to a researcher career? How it is evaluated by a scientific researcher/University admission...

02 March 2021 9,661 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

How to eliminate Steady state error from Reinforcement learning genetic algorithm code?

The following code (see 1st 2 images attached) is used to produce PID controller values that are designed to control the system (G). The code finds the PID controller values (noted as k) by using...

28 February 2021 6,560 14 View