Spacecraft attitude error dynamics simulation

Samira Eshghi @Samira_Eshghi

08 August 2014 1 9K Report

Anyone can help with spacecraft attitude error dynamics simulation?

Ibrahim Chouaib

Spacecraft Dynamics and Control Dr. Chris Hall, Randolph Handouts can be helpful.

http://www.dept.aoe.vt.edu/~cdhall/courses/aoe4140/

Badges
Science topic

Similar topics
Social Psychology
Attitude

More Samira Eshghi's questions See All

Can anyne share a simple SIMULINK/MATLAB file that shows the implementation of a control system with random sampling?

I need help in understanding the role of (random) sampling in implementation of a control system in Simulink. I need a basic, general example to visualize the role of the sampler in a control...

03 April 2018 3,856 3 View

How can we compare energy consumption of different data sampling mechanism in MAS?

The frequency of data sampling differs in commonly used mechanism such as uniform, nonuniform, random, event-triggered etc. Less frequent sampling saves energy. How do we compare energy...

02 March 2018 8,899 1 View

Any recommendation for a sample of research frame (Concept Map) work on Formation Flying?

Hi I'm conducting a literature review on Formation Flying. While there are numerous studies and surveys on the subject, I have not been able to find a well-structured concept map on the general FF...

08 September 2016 9,064 2 View

How can I perform fractional powers of vectors in Matlab to avoid domain error?

I'm trying to perform fractional power for a vector containing both positive and negative values. The power is not an integer so the Simulink fails to perform the operation and gives out the...

31 December 2014 8,611 8 View

What could cause divergence in results obtained from a pure simulink simulation and one with subsystems substituted by embedded matlab functions?

I have simulated a system using pure simulink blocks. Later I substituted some of the subsystems by commands in a matlab embedded function. The results are completely different. What could cause...

10 November 2014 8,627 6 View

Is it reasonable to approximate the quaternion error that is generally represented by the quaternion multiplication by a deduction for small angles?

In page 21 of this lecture note, quaternion error approximation for small errors has been defined as the deduction of the desired from current. It does not make sense mathematically speaking....

09 October 2014 3,686 1 View

Will I have better opportunity to pursue PhD if I change my firld of study from aerospace engineering to control system engineering?

The primary focus of my master thesis is control system design, the plant on which the control approaches are implemented is associated with aerospace engineering. Will I have better chance of...

05 June 2014 4,886 5 View

What is the general idea of using Jacobian in control problems?

What are the advantages of using Jacobian in control problems?

04 May 2014 6,696 4 View

How can I identify the underpinning causes of singularity error in Simulink?

The singularity error identifies the block in which the problem occurs (e.g.Integrator), however, the problem initiates in other part of block which finally causes singularity in integrator. What...

03 April 2014 4,666 5 View

What is the general principle of designing the switching control in sliding mode control?

It could be taken as u_sw=-(1/b)ksgn(s) where k is defined as in Applied nonlinear Control by slotine. Does the definition vary for advanced SMC like non-singular terminal SMC?

02 March 2014 2,095 6 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

Arena simulation - how do i model the following model in ARENA (see description) (new to ARENA)?

Hello, I'm fairly new to ARENA and I have the following problem: I have two queues in which, in each queue, a different order type arrives (both having an arrival rate of exponential 10). Order...

02 March 2021 2,431 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Why the results when using wall thickness and when using shell conduction are different in ansys fluent?

Actually, I am running cfd simulation for a heat exchanger which has two fluids one hot and other one is cold fluid. there is a solid domain between them, which I removed and instead I have used...

01 March 2021 9,537 2 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

In Molecular Dynamics Simulation, how do I make changes to the force field according to my protein?

Hi In Molecular Dynamics Simulation, how do I make changes to the force field according to my protein? I got this error in the add-ion stage: Fatal error "./ amber99sb-ildn-HHH.ff / force...

01 March 2021 8,747 4 View

How can you bring two structures together to create an adhesive bond in LAMMPS?

I have created an Ice 1h crystalline structure and an Aluminium substrate structure and equilibrated both at 250K. Now I need to bring them together in a way that an adhesive bond is created....

01 March 2021 3,325 2 View