Sometimes the side of concrete bridges is observed to turn black in colour. What is the reason for this phenomenon?

More Thulfiqar Salim Hussein's questions See All

How do engineer determine the number of cells for concrete box girder bridges?

08 September 2018 9,780 2 View

In joints of precast concrete bridge segments, what are the functions of applying epoxy adhesive?

08 September 2018 3,952 8 View

If on-site slump test fails, should engineers allow the contractor to continue the concreting works?

08 September 2018 7,060 8 View

Are diaphragms necessary in the design of concrete box girder bridges?

07 August 2018 9,089 5 View

What are the problems associated with this method in terms of shrinkage of concrete?

In bridge widening projects, the method of stitching is normally employed for connecting existing deck to the new deck.

06 July 2018 2,198 4 View

In the design of elastomeric bearings, why are steel plates inserted inside the bearings?

06 July 2018 5,505 6 View

Pick up the correct statement regarding low heat cement from the following?

A.It possesses less compressive strength B.Its initial setting time is about one hour C.Its final setting time is about 10 hours D.Its mainly used for mass concrete work E.All the above.

06 July 2018 2,641 2 View

What are the functions of column in a building?

06 July 2018 5,468 1 View

Does Water damage concrete?

06 July 2018 1,183 4 View

What is the cement sand & aggregate ratios for various grades of concrete mix?

06 July 2018 8,515 1 View

New Journal, "Integrative Psychological and Behavioral Science" -- do you not know, and have you not seen, this done before?

Question to you and THEM, the New Journal, "Integrative Psychological and Behavioral Science" -- do you not know, and have you not seen, this done before? There appears to be a core problem for...

02 March 2021 3,024 2 View

What is the procedure to determine the permeability of concrete?

can anyone help me in this, it will help me with my research work

01 March 2021 834 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

Does any one can help me choose a reasonable basis set for intermediate metal ions interactions with guanine (i.e Fe2+, Mn2+, Cu2+ and exc.)?

Hello every body Does any one has any idea to help me choose a reasonable basis set for intermediate metal ions (i.e Fe2+, Mn2+, Cu2+ and exc.) interactions with guanine or other DNA organic...

01 March 2021 6,187 2 View

Apart from Nanosilica and CNT's what are the other nanomaterials readily available to use in concrete mixture?

Nanotechnology in concrete materials

01 March 2021 3,379 3 View

What could be some reasons why unstimulated monocytes are getting activated?

Im doing PBMC isolation -> CD14+ enrichment using magnetic beads -> stimulation setup. My negative control is just cells in cRPMI but they seem to get activated over and over again.

28 February 2021 7,883 3 View

Why does intensity drops as concentration increases?

Is there any reason for decrease in fluorescence emission intensity of HSA,BSA when increase the concentration ?

28 February 2021 3,653 4 View

POlymer+DMSO solution and moisture??

What could be the reason of moisture at the sides of Vial when I am preparing my polmyer+DMSO solution for membrane fabrication? What etiquettes I am possibly missing here?

28 February 2021 6,516 5 View

Concrete compressive strength databases?

I am looking for datasets similar to this one: http://archive.ics.uci.edu/ml/datasets/Concrete+Compressive+Strength I am looking for concretes with different types of aggregates (Recycled,...

27 February 2021 6,801 3 View

Should we reduce the standard unit of length to 0.31951540592 meter ?

The reasoning behind this question is to align the ratios of the proton potential in energy per charge to the speed of light in distance per time. As these two dimensions appear to be related,...

27 February 2021 947 7 View

Israa Dahham

interested

Thulfiqar Salim Hussein

Thanks

Zaid Abdul Zahra Mahdi

Thanks for all

Marwah M. Al-Khuzaie

Thank you very much

The answer is:

In some cases, it may be due to the accumulation of dust and dirt. However, for the majority of such phenomenon, it is due to fungus or algae growth on concrete bridges. After rainfall, the bridge surface absorbs water and retains it for a certain period of time. Hence, this provides a good habitat for fungus or algae to grow. Moreover, atmospheric pollution and proximity of plants provide nutrients for their growth. Improvement in drainage details and application of painting and coating to bridges help to solve this problem. Reference is made to Sandberg Consulting Engineers Report 18380/X/01.