Can anyone send me article talking about CFX code and relation with thermal fluid?

04 May 2017 8,494 0 View

Can I submitted in thermal energy?

04 May 2017 8,475 2 View

Who can show me the calculus of heat transfer in natural convection ?

03 April 2017 4,535 0 View

Enhancement of heat transfer and the volumetric flow rate (m^2/s)

i have finding difficulties to draw volumetric flow rate"Time series of the flow rate cross the center line (x = 0) in the cases with a fin."in cavity with High H.the formula(7) fig.5.please helpme

08 September 2016 1,109 0 View

How to calculate Ti in cavity just with formula

Hi,my work now is on thermal cavity filled water I want to calculate the initial temperature and the change between tc and e delta T = Th-Tc with Ra = 2.08 * 106 and the Prandtl number Pr = 6.98.I...

06 July 2016 2,781 5 View

Hi , how do you calculate T=-1/2 and T=1/2 at sidewalls?

04 May 2016 1,057 2 View

Can anyone suggest a program wich use an open file *.dat and use it in equation in order to get solution of function ?

Hi, I want to plot Nusselt as function with time and try to suggest how I can do it. if it is possible reguards

01 January 1970 3,169 1 View

Can you send me your article?

Hi, Iw'd like receive your article as pdf in mail:[email protected] Tk

01 January 1970 6,825 0 View

Please, link for films cooling?

Hi,everyone I would like the one of you my cheres to send me articles or link for films cooling.

01 January 1970 8,351 0 View

Can I submitted in thermal energy?

01 January 1970 8,227 4 View

Can I put a figure that was drawn by Bio-Render in publication paper?

I want to publish paper in journal but I have figures which have drawn with bio-renders, can I put them in the paper or which other software I can use to draw them?

27 February 2021 8,179 1 View

How to approach CFD simulation results of a flow past a cylinder?

Hi all, I'm doing a transient simulation of flow past a rectangular cylinder close to the free surface. As far as I'm concerned, the common practice is to discard the initial stages of the...

25 February 2021 1,348 3 View

No streamlines present in a small region inside a flow. This means exactly what?

No streamlines present means whether the flow is getting obstructed there and the velocity inside the region is zero? Or else, the fluid is trapped inside that region with a nonzero velocity?...

22 February 2021 5,249 10 View

Can't recognize exact phase and PDF card no of Silicon carbide in XRD?

We have deposited silicon carbide on carbon substrate using one PVD technique. Due to amorphous behavior of SiC at low deposition temperature, we performed heat treatment of those films at...

22 February 2021 2,072 3 View

Which Journals would you advise to submit a Letter which briefly talks about neurosurgical treatment of neuro-oncological patient during Sars-COV-2?

Possibily not an open access journal which does not add any publishing costs once being accepted. Thank you in advance

09 February 2021 717 6 View

How to do mono formylation of N,N-diethyl-3-methoxybenzamide?

I have attempted the formylation of the above mentioned compound using a very well reported protocol using secondary Butyl Lithium and TMEDA at - 78 degrees Celsius. I have done it quite a few...

08 February 2021 2,793 2 View

Recommendations for sample size in visual qualitative research (using children's drawings)?

Hi everyone! Asking for a little help, if I may. I am working on a research project, where I aim to analyse children's drawings about Covid-19. I am fairly new to using visual data in qualitative...

07 February 2021 9,530 3 View

Best way to draw COLONY output / pedigrees?

Hi, I am using the sibship analysis software COLONY 2.0.6.6 (most recent version) on about 150 individuals offspring, with some of them as potential fathers and mothers. COLONY provides a lot...

02 February 2021 6,910 2 View

How to plot 3D plot for Measured value of antenna?

Hello everyone, I am trying to plot a 3D pattern from measured data of antenna in the MATLAB, for this, I have many files for one GHz frequency at different theta(e.g theta 90,80,70, etc). My...

31 January 2021 8,458 2 View

Why can't ANSYS Mechanical APDL detect the volume of my design ?

The 1st image shows the moment when I import my design(IGES) into the Mechanical APDL. The 2nd image occurs when I wanted to Operate>Boolean>Divide Volume By Area. The design is a regular...

28 January 2021 2,962 3 View