What is the most reliable source to get Impact factor of journals?

Source to get Impact factor of journals

01 March 2021 6,654 2 View

Is anyone familiar with the cyclic compressive fatigue testing (BS EN 12697 - 25) ?

I would like to get more information on the cyclic compressive fatigue testing (BS EN 12697 - 25) which is typically done for bituminous material in pavement design. Any one can advise on the...

28 February 2021 2,004 3 View

How to calculate Ligand-active site distance in a ligand-protein complex from MD simulation?

I have run a MD simulation of a ligand-protein complex in GROMACS using CHARMM forcefield. Reviewer has asked me to calculate Ligand-activesite distance and binding free energy of ligand with...

27 February 2021 4,703 1 View

Why initial concentration of Pb not the same as calculated one when testing using AAS?

I am currently doing research on the adsorption of heavy metal using magnetic reduce graphene oxide. I use AAS to determine the concentration of the heavy metal. I prepare the Pb solution with...

26 February 2021 9,580 4 View

Stress/strain tensors decomposition ???

25 February 2021 6,760 1 View

How to indicate the degree of litter decomposed by microbes?

Any technique could detect the degree of litter decomposed by microbes? Or any indexes could do this job? I want to split the contribution of microbes during decomposition, so any suggestions...

23 February 2021 1,362 5 View

How to Implement Elastoplasticity in a PCL model in COMSOL Multiphysics?

I am using COMSOL Multiphysics 5.5. I am trying to simulate the tensile test of PCL scaffolds. However, regardless of the strain, I have the elastic region all the time which is not true when it...

23 February 2021 4,050 1 View

Best FE Program for Concrete Strengthened with FRP Sheets?

Colleagues, I have been using ANSYS to model concrete strengthened FRP sheets, but less than happy with it. Any has recommendation for efficient, easy to use FE program for modelling concrete...

22 February 2021 7,528 3 View

Any information about dinitrosalisylic acid reagent end point color stability ?

I work on estimation of alpha amylase activity using dinitrosalisylic acid reagent If i put the reagent to stope the enzymatic reaction and allow the reagent to react with the produced reducing...

17 February 2021 7,402 4 View

Using liquids as superstrate in Fabry-Perot Cavity Antenna?

Hi, A Fabry Perot Cavity allows to increase the directivity of a low gain antenna by putting in the top of cavity a superstrate with high permittivity such as a ceramic (er=10.2). However,...

09 February 2021 6,799 8 View

What is the best way to keep an anaerobic chamber anoxic in the absence of hydrogen?

I'm a graduate student who works with an anaerobe, so I often work in an anaerobic chamber. I've been working on an assay that involves the steady-state of the quinone/ quinol pool. Anoxic...

03 March 2021 2,971 1 View

What is the production process of CaFe ferroalloys?

I looking for ferro calcium production process

03 March 2021 1,755 4 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

12% ledeburitic cold work tool steel, etched for revealing retained austenite, any help for clarifying?

Hello everyone. Given microstructure image belongs to a 12% ledeburitic cold work tool steel (annealed and tempered). The sample was etched with picral (100 mL ethanol and 4 g picric acid). I...

02 March 2021 4,119 3 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View

Why Austenite grains in steel show much more twinning than ferrite grains?

It is oftentimes said to be a distinctive metallographic trait that differentiates a fully austenitic and a fully felly ferritic steel without etching that might distinguish between two. Why...

02 March 2021 728 2 View

How Can I bring as much common elements in steel as possible to calculate stable phase(s) in OpenCalphad?

As I was tweaking step-by-step OpenCalphad6 Macros step1.ocm involving phase and thermal property calculation of a High-speed steel, I could not incorporate more than 6 elements in the steel...

01 March 2021 8,840 1 View

I need to accelerate corrosion in steel parts that are used in a salt-water environment. Is there a technique for doing so?

I have a structure that employs d-ring swiveling tie-downs that corrode during use and become "frozen". I have sample swivel assemblies that I wish to corrode to see if I can free them using one...

01 March 2021 3,739 3 View

Which cell line should we use to perform biological dosimetry experiments?

We are preparing some experiments based on irradiating cells under different conditions in order to evaluate the effects in terms of DNA damage, genetic expression, etc. As our project is...

01 March 2021 3,355 3 View

Is there a deep reason for using the squared modulus of the wave function as the probability density of the existence of the particle?

I think we were all surprised at the first time we got to know quantum mechanics that the squared modulus of the wave function is the probability density of the existence of the particle? The role...

28 February 2021 6,282 9 View