03 March 2016 2 7K Report

Is there any journal, reference or application that describes the effect of increasing strain on a steel alloy 42CrMo4 during forging process? 

More Jibin Babu's questions See All
What is the relation between mole fraction/mass fraction with temperature during a phase change process?

During a condensation process,at a particular temperature the water vapor condenses into water liquid. How can we relate the mole fraction/mass fraction of vapor with temperature? formula relating...

31 December 2016 5,466 4 View

Is there any journal, reference or application that describes the effect of increasing strain on a steel alloy 42CrMo4 during forging process?

Is there any journal, reference or application that describes the effect of increasing strain on a steel alloy 42CrMo4 during forging process? how tdoes the change in strain or percentage height...

02 March 2016 2,572 0 View

Calculating compressive stress

How can we calculate compressive stress in case of a forging process? Is there any formula that can be employed for calculation of compressive stress uding initial and final dimensions of a forged...

01 February 2016 742 3 View

Similar questions and discussions
What is the production process of CaFe ferroalloys?

I looking for ferro calcium production process

03 March 2021 1,755 4 View

12% ledeburitic cold work tool steel, etched for revealing retained austenite, any help for clarifying?

Hello everyone. Given microstructure image belongs to a 12% ledeburitic cold work tool steel (annealed and tempered). The sample was etched with picral (100 mL ethanol and 4 g picric acid). I...

02 March 2021 4,119 3 View

Which is the most efficient etching solution for nickel based alloys?

Which solution reveals the microstructure and features of nickel-based alloys?

02 March 2021 2,221 3 View

Why Austenite grains in steel show much more twinning than ferrite grains?

It is oftentimes said to be a distinctive metallographic trait that differentiates a fully austenitic and a fully felly ferritic steel without etching that might distinguish between two. Why...

02 March 2021 728 2 View

New Journal, "Integrative Psychological and Behavioral Science" -- do you not know, and have you not seen, this done before?

Question to you and THEM, the New Journal, "Integrative Psychological and Behavioral Science" -- do you not know, and have you not seen, this done before? There appears to be a core problem for...

02 March 2021 3,024 2 View

How to add a journal?

I would like to know how to register the journal Flora Montiberica (ISSN 1138-5952 - eISSN 1988-799X) in Research Gate.

02 March 2021 8,156 2 View

Is it possible to remove a preprint posted by a journal which is already rejected?

As we know many journals are posting preprints (DOI) in advance before the peer-review process. However, there is no guarantee that the preprints get published. The journal's reviewers undergo the...

01 March 2021 5,778 2 View

How Can I bring as much common elements in steel as possible to calculate stable phase(s) in OpenCalphad?

As I was tweaking step-by-step OpenCalphad6 Macros step1.ocm involving phase and thermal property calculation of a High-speed steel, I could not incorporate more than 6 elements in the steel...

01 March 2021 8,840 1 View

No title

Hi, I have several doubts about one paper (Systematic Literature Review) that was rejected. The main topic is Single-Board Computers in engineering education during the period 2010-2020. The...

01 March 2021 9,015 3 View

I need to accelerate corrosion in steel parts that are used in a salt-water environment. Is there a technique for doing so?

I have a structure that employs d-ring swiveling tie-downs that corrode during use and become "frozen". I have sample swivel assemblies that I wish to corrode to see if I can free them using one...

01 March 2021 3,739 3 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close