S-N curve for Hot working tool steel?

Bartłomiej Dybowski @Bartlomiej_Dybowski

05 May 2018 0 5K Report

Dear All,

Does anybody is able to share the S-N curve for hot working tool steel with chemical composition: C 0.38; Si 0.30; Mn 0.75; Cr 2.6; Mo 2.25; V 0.9 or similar? The steel condition: quenched and tempered.

Best regards,

Badges
Science topic

More Bartłomiej Dybowski's questions See All

Is formation of Al-Zr Dispersoids possible in the as-cast HPDC AlSi9Zr alloy?

Hello, I'm investigating AlSi9 high pressure die cast alloy, modified with Zr (more than 0.1%). The alloy is designed to operate in as-cast state, without and heat treatment. My question is what...

10 November 2016 5,749 7 View

Does anybody have an experience with revealing grain in the aluminium silicon casting alloys?

Hello, I need to reveal the grain structure in the aluminium silicon casting alloys. I have tried many etchants: Kellers, NaOH, HBF4 and some more, neither of them give acceptable results even...

31 December 2015 3,459 27 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

What should be the sample container for the hydrothermal reaction in a microwave reactor at 180 °C for 10 min at the heating rate of 5 °C per minute?

Suggest one of them 1. Teflon-lined stainless steel autoclave: 2. Alumina (Al2O3) ceramic container

30 July 2024 7,326 1 View

What is the best method to detect the chemical composition of pollen ?

I have multiple small samples of grass pollen with anthers. I want to find a method to identify concentrations of proteins, lipids, and other various elements for these samples. any suggestions?

28 July 2024 5,331 1 View

Will the catalytic effect of retained austenite happens in steels including RA?

The catalytic effect of retained austenite refers to the phenomenon wherein quenching steels with a small amount of retained austenite, when subjected to tempering at a specific temperature...

27 July 2024 8,508 0 View

Please investigate the effect of temperature and strain rate of hot deformation and the formation of delta ferrite in martensitic stainless steel 410?

25 July 2024 9,408 0 View

How to saturate steel samples with hydrogen?

I have tried to saturate ferritic steel with hydrogen using the electrolytic method and H2SO4. However, the effect was very poor even after 3 days of "saturation". Can anybody help in choosing a...

24 July 2024 4,393 2 View

Hi dear researchers, do you suggest the best and shortest path for chemical synthesis and green synthesis of magnetite(Fe3O4)?

Suggest the best and shortest route for the chemical synthesis and and green synthesis of magnetite(Fe3O4) The chemical synthesis should contain the least dangerous chemicals along with full...

21 July 2024 2,476 2 View

Why do fish have fishy odors naturally ?

Chemical Engineering /Food Engineering

20 July 2024 4,152 4 View

Masonry Interaction Module ABAQUS?

I am simulating interlocking / dry stacked masonry in Abaqus. I am using a friction coefficient of 0.6 for my model as it is stated in the previous research as well as in the base paper. The...

16 July 2024 5,047 0 View