Statistical analysis via Analysis of Variance (ANOVA)?

Hello Everyone I hope everyone is doing well. I have one article in revision process in Construction & Building Materials and reviewers' are asking to do statistical analysis. However, I...

31 October 2020 7,233 5 View

How the band gap in CNTs can be tunned?

CNTs can act as mettalic as well as semiconducting and I beleive that it can be controlled through band gap.

29 August 2020 9,765 9 View

Clinical Trail: How can we justify statistically a CT when it fails at final stage?

When a clinical trail succeed in first trails and fails at final trail,please write me, how could we justify the cause behind its failure statistically.

10 August 2020 8,035 3 View

Can all network UE decode the information transmitted by a eNB through Physical Downlink Control Channel (PDCCH)?

A wireless network consisting of two UEs (A & B) and an eNB. The eNB transmits control information to UE A through PDCCH. Can UE B also decode this information? Or is it permissible for UE B...

07 August 2020 2,628 2 View

What is the Distance Distribution of random point in a clustered environment?

How to find the distance distribution of a random point in a cluster from the origin? I have uniformly distributed cluster heads following the Poisson point process and users are deployed around...

04 March 2020 6,134 3 View

How to find the residual stresses in carbon fibre composites. Will XRD work for the same?

Respected all, I want to know about the correct method to find out the residual stresses in the carbon fibre reinforced composites. The literature says that XRD can get residual stresses. However,...

30 January 2020 486 13 View

Can you help in providing Support Vector Regression code for forecasting of solar power?

I have data on power generation and other variables (e.g Irradiance, temp & wind speed) of last two years(on daily basis). I want to forecast the power generation using SVR so I need its...

07 October 2019 4,541 2 View

How to remove DMSO from a solution?

I want to remove DMSO from a solution, without heating above 70C, DMSO we used to make solution with PANI.

15 September 2019 4,696 5 View

If the intensity of XRD peaks is very high about 500K, what does it mean?

i sysntesized sample by Ball milling and then heated it at 700 C, i got the pure phase with low intensities about 10K, then after annealing at 1000C, i got the intensities peaks about 100K-500K,...

18 July 2019 1,642 3 View

Can anybody help me in tracing the availiblity of some published articles?

08 January 2019 3,634 2 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View

Can we classify HV and LV lines based on line length?

I have dataset which shows the length of power lines. I need to classify the lines based on the line length. Is there a rule to classify the High voltage (HV) and low voltage (LV) lines based on...

03 March 2021 4,116 4 View

What is the production process of CaFe ferroalloys?

I looking for ferro calcium production process

03 March 2021 1,755 4 View

How to find the mean, SD and CI in SPSS?

Hi, I hope that someone can help me with this task: I have 5 groups of participants which are numbered in SPSS from 1 to 5 (according to their group number) and are all under the variable group....

03 March 2021 506 3 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View