I'm trying to start a culture of IMR90 and they do not seem to stick to the bottom of the flask. I coated the flask with collagen to help adherence, I'm using this media: EMEM with 10% FBS. Please help.
Dear Joannie Lemaire
Consider the attached protocol.
Dear all, One of the key points in TSAD (Time Series Anomaly Detection) when using a sliding window is the size of the window. For (quasi)-periodic time series, methods such as AutoPeriod,...
13 May 2024 920 3 View
Hi, We have been having some curious contamination in our cell culture. We have suspension cells and the media looked fine, no smell no signs that there was contamination. But under the...
22 February 2023 3,014 5 View
We receive samples from different vendors from mouse studies. For the sample taken in life, some vendors can't tell us what volume is in the tube since it would take too much time to note every...
07 December 2022 7,087 2 View
Would the passage of a big IDP (Interplanetary Dust Particle) passing at some distance not be an alternativeand perhaps more likely source of such soliton events?Just like those propagating in the...
06 April 2015 3,981 4 View
High energy astrophysicsts and Nuclear Physicists
19 December 2014 2,377 8 View
Any idea will be a great help. Thank you. :)
20 August 2014 7,939 8 View
Which device aides in decreasing BSI?
28 July 2013 5,480 1 View
Investigation on a SmallSat CMOS image sensor for atmospheri...
01 January 1970 7,967 0 View
How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...
10 August 2024 942 3 View
I have carried out MFC experiments on three different volumes, 50, 500 and 1000 mL of wastewater. Results after MFC treatment shows that TDS and EC are more in larger volumes of water i.e. TDS and...
09 August 2024 9,621 0 View
Hello everyone! I observed in my culture (htert-RPE1 cells) an orange- red particle at the bottom of the dish. It is visible to the naked eye as a very very small red dot. Could it be a...
09 August 2024 2,824 3 View
I did PR spin coating on trench structure. I used AZ P4620 PR and the thickness or PR is around 11um. The substrate is Si. And my trench structure depth is 141um(negative way). Even though I...
08 August 2024 2,298 0 View
I am working in fungal fermentation of soybean meal and there is bacterial growth in them at times. I am trying to quantify fungal cell counts and bacterial cells; but I haven't been able to do at...
07 August 2024 7,535 4 View
I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.
07 August 2024 4,526 4 View
Hi, I have a question about normalizing the MTT OD values for doing the statistical analysis. So, if we have 3 different plates and we call them 3 different replicates, so, first we would...
07 August 2024 8,106 4 View
Previously when I co-coluture anti-CD19(FMC63) CAR-Jurkat with Raji with E:T=5:1, Jurkat can eliminate Raji in 24h. However, when I test another CAR construct, although I can dectect totally CD69...
06 August 2024 641 2 View
I have tried several times to isolate lymphocytes from mouse spleen, but all attempts have been unsuccessful. I tried most available protocols. I used different dissociation media (HBSS with Ca...
04 August 2024 9,913 7 View
I have protein-membrane simulations (PDB, PSF, DCD) and have noticed that water molecules near the protein are not visible in the simulations. How can I fix this issue? Is there a way to place the...
04 August 2024 1,200 2 View