Problem of running Ansys with matlab?

09 September 2016 0 5K Report

I am running ansys(apdl) by matlab using the command :

System.....

However, after some minutes ansys is stoped! I am pretty sure that there is no Problem in ansys Code! Can anyone help me?

Badges
Science topic

More Hadi Hatefi's questions See All

How to get Strain/stress result in APDL while using Elements with mide Nodes?

I am modelling a specimen in APDL using SOLID186 and running static loads. While getting the results at specific Locations using Node(x,y,z) commands, Ansys gives me Zero! since it select the mide...

06 July 2016 8,344 6 View

How to write dat into a file in APDL?

I am using vwrite to write my results into a text file, however, its nor working, I dont know the format...

03 April 2016 1,870 0 View

How can I merge to parts of model in Ansys ceated by different methodes, one direct(using directly nodes) the other keypoints?

I wana model 3D crack, to have singular elements, I had to create elements manually, I mean using direct appoarch for modelling(creating nodes) however, the other parts of model have been created...

31 December 2015 5,269 0 View

Exporting Geometry from work bench to APDL?

Does anyone know how to export Geometry from Ansys workbench to APDL? I have modeled in ansys Work Bench, but now I need to change to APDL. Also I need to know the coordinate of point which I...

10 November 2015 4,407 1 View

Dear all, I was wondering if anyone knows whether MGLtools and Autodock can run on Mac OS?

I have tried to download the 64-bit version of MGLtools however, as many times as I have downloaded and uninstall the programs, an error arises that the app needs to be updated. Thank you.

03 March 2021 5,997 2 View

I got 02 moderator values defining Johnson-Neyman significance regions. Is it an error?

Hi everyone, I am conducting research for my Master's thesis. I am using PROCESS by Johnson-Neyman to analyze my Moderator model. I test the relationship between Public Service Motivation and...

03 March 2021 2,350 2 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Do I need to do linear regression before running mediation analysis using PROCESS MACRO by Hayes ?

I just wanted to check if I need to run a linear regression separately if I am using PROCESS MACRO to run mediation analysis. Thank you.

02 March 2021 4,359 3 View

How to code open-ended questions in SPSS?

Hello all, In SPSS I am going to code 2 open-ended questions. I have already read all the answers and I made a list of the most important categories to which I can code the answers. This question...

02 March 2021 1,757 4 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Do I need to strip the PVDF membrane before staining it with colloidal gold?

Dear Colleagues, After running Western blot on PVDF membrane and detection using ECL, I would like to stain my PVDF with colloidal gold to be able to allign the ECL image with total proteins on...

02 March 2021 7,829 3 View

PACYC PCR not working after several attempts. Would anyone have any suggestions?

So, I have been trying to run a pACYC PCR which will be used later on for a Gibson Assembly. However the PCR is not working. I have already tried gradient PCR and changing extension time; however...

02 March 2021 1,146 2 View

What SPSS analysis should I run with one IV (with two levels) and two DVs?

Hi, I am trying to figure out which test would be most appropriate to run for the following question: Is there a difference in task blood pressure between smokers and non-smokers? There are two...

01 March 2021 8,235 2 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View