Printer material powder?

07 July 2018 0 3K Report

Can you anyone help me how and what are the parameters were found in selection of Printer, copier , powder material.

Badges
Science topic

More Arun Thangarajan's questions See All

Any one help me regarding to choose graphene nanocomposites or gallium arsenide or Zirconium nitiride to enhance the silica efficiency?

We are working on the platform to enhance the silica efficiency on renewable energy resources. Literature and journal supported these three materials can enhance efficiency in somewhat better, but...

06 July 2018 8,367 0 View

How can i prepare water based drilling mud at lab for testing API FILTER PRESS, VISCOSITY, GEL STRENGTH.? Materials and Quantities?

I need to prepare the drilling mud and prepared mud to be tested for API filter press, Viscosity, Gel strength? So how much of materials and how much amount of materials to be added for water...

04 May 2018 1,819 0 View

Can anyone tell me which is best book to learn about CFD and also Matlab Programming?

MATLAB AND CFD

31 December 2017 4,412 0 View

What is the status of bread making and more bakery foods with the use of insect flour/powder?

Insects have been consumed by human diet since prehistoric times. At present, the idea of looking at insects as food has been getting traction worldwide, also in response to increasing food...

03 March 2021 6,223 5 View

How to grow E.coli on the low salt LB agar plate with 50 or 100ug/ml of Blasticidin?

Hello, I would like to ask how to grow E.coli which resists 50 or 100ug/ml of Blasticidin. I have tried many methods by using low salt Luria-Bertain(LB) agar plate. However, no colonies grow. Let...

01 March 2021 2,027 2 View

Have anyone checked before Cyclic voltammograms of intial ITO substrate and E-teck?

As a beginner in electrochemistry, I tried to obtain cyclic voltamograms of commercial anatase powder deposited on an ITO substrate or on Eteck. After several attempts, I noticed that my cyclic...

23 February 2021 3,175 3 View

How to reduce static electricity of powder after lyophilization?

I am working on synthesizing and then purifying peptides using the SPPS system. After purification of the peptide, the peptide powder is obtained using a freeze dryer. When measuring the powder,...

22 February 2021 10,099 5 View

What kind of steel moulds are used for hot pressing metal powders?

My main concern is that the metal powders should not weld to the mold surface and I should easily be able to eject out the pressed samples. I am looking for alternative for graphite moulds. The...

22 February 2021 2,965 4 View

How to Study a proton NMR of Graphene prepared by Electrochemical Exfoliation technique?

I performed a Proton NMR of graphene powder prepared by electrochemical exfoliation technique. It shows some peaks. But I can't understand it.

21 February 2021 8,947 3 View

Are ZnS nanoparticles moisture sensitive?

Hello Everyone, I tried to form ZnS nanoparticles using the hot injection method and was able to form the same (confirmed by XRD). When I centrifuged, after the reaction I got a kind of white...

17 February 2021 1,709 3 View

How does a freeze dryer destruct your solid sample?

Several times I lost my sample during freeze drying. There was no solid or powder in the vial after freeze drying. I'm sure sample contained solute because i took its NMR spectrum. I covered the...

15 February 2021 6,749 2 View

What is role of toluene and stearic acid in ball milling for powder ? In what weight percent we should add this to powder?

I am doing ball milling operation of Aluminum and silicon carbide powder. I am pretty confused about what should be added as process control agent ? what is role of toluene as PCA and stearic...

12 February 2021 5,205 3 View

Is there any method that we can electrochemically oxidize a powder?

I am working with a material which is sensible to water and oxygen, I would like to oxidize this powder either chemical or electromagnetically. Does anyone knows a method to electrochemically...

09 February 2021 2,944 3 View