In Salve mode of DSPACE 1104 PWM ?

08 September 2016 6,515 0 View

Power factor correction

In power factor correction I have seen many paper they use PLL to generate reference signal. but it is also possible to sense input voltage and generate reference signal. is it mandatory to use PLL ?

04 May 2016 2,556 9 View

How can we tune fuzzy logic controller in simulink for dc-dc converter ?

03 April 2016 7,612 0 View

How can we connect simscape block of simulink to simpowersystem block e.g. variable resistor(simscape element) as load in any electric circuit.....?

??

08 September 2015 2,661 0 View

How can we connect simpowerblock and variable resistor of simscape ?

Your toughest technical questions will likely get answered within 48 hours on ResearchGate, the professional network for scientists.

08 September 2015 7,700 0 View

I am doing simulation using MATLAB Simulink. A SEPIC power factor converter with simulation step "1e-6" ode23tb of switching frequency 30 Khz?

07 August 2015 3,612 1 View

How can we get differentiation of signal in matlab simulink, if signal is part of power electronics converter circuit with switching frequency 30Khz ?

How can we get differentiation of signal in matlab simulink, if signal is part of power electronics converter circuit with switching frequency 30Khz ?

06 July 2015 1,948 2 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

Can we classify HV and LV lines based on line length?

I have dataset which shows the length of power lines. I need to classify the lines based on the line length. Is there a rule to classify the High voltage (HV) and low voltage (LV) lines based on...

03 March 2021 4,116 4 View

Irradiation data for JAPAN?

Hi, Could you help me to get the latest (2019, 2020) solar resource data for a particular site in JAPAN? PV GIS and NSRDB data are not in reach to JAPAN, I'm looking for some other database for...

03 March 2021 961 3 View

Arena simulation - how do i model the following model in ARENA (see description) (new to ARENA)?

Hello, I'm fairly new to ARENA and I have the following problem: I have two queues in which, in each queue, a different order type arrives (both having an arrival rate of exponential 10). Order...

02 March 2021 2,431 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Is SSRN e-Journal Scopus indexed?

I have publication in SSRN. I want to know whether it is Scopus indexed? Does it show impact factor? What is its ISSN No.?

02 March 2021 4,565 3 View

Is there a powerful system for the security of the systems distributed on IoT systems?

Is there a powerful system for the security of the systems distributed on IoT systems?

02 March 2021 3,858 10 View