Potential monitoring system for shakers in CO2 incubators?

26 August 2017 1 1K Report

We are looking for a monitoring system like this for our plate shakers in our CO2 incubators:

https://www.thermofisher.com/order/catalog/product/SMARTKIT1

One of our shakers failed during the weekend for at least hours before the next person went into lab to feed cells. We want to prevent this from happening again in the future by putting some kind of monitoring system on the shakers so that at least someone gets the alert. That way, we would be able to attend to the shaker more quickly.

Please let me know if this kind of monitoring system is available. Or if anyone has any "DIY" suggestions, please also let me know. Thank you!

Anoop Kumar Srivastava

Please have a look at these attachments..

Badges
Science topic

More Charity Juang's questions See All

How do you eliminate orbitrap electronic noise m/z peaks?

I have 2 m/z peaks that will not go away. not solvent/column/online or offline they are always there. I was told they are prob electronic noise peaks. Does anyone know how to isolate the...

20 December 2018 5,238 2 View

Waters 2707 HPLC autosampler problem?

I am using a 2707 waters HPLC device. When I try to inject a sample, it says missing plate or rack. I changed the needle and calibrated its position but I still get the same problem. I even get...

02 March 2021 1,408 1 View

Should we change media after1st 6hrs after plating HUVEC bought from INVITROGEN?it's not recomended by invitrogen.Will DMSO present in stock matter?

We have HUVEC bought from Invitrogen. Cat no -C-003-5c. while first plating the cells we have bought the protocol suggests not to centrifuge the cell with media to remove the DMSO. Should we...

02 March 2021 3,713 2 View

How to normalise data on OPM package from R Studio ?

Good afternoon, I recently used OmniLog from BIOLOG for my experimentations : I tested the metabolism of different strains on 2 types of plates. I have 16 strains of 3 different groups...

02 March 2021 3,584 1 View

How to quantify carbon deposition on CuZnAl catalyst?

Dear All, I want to quantify carbon deposition on the surface of the CuZnAl catalyst. I have tried thermogravimetric analysis, but I've got weight gain as the active Cu- get oxidised. Does anyone...

01 March 2021 1,907 3 View

Why Trivalent chromium start precipitating above PH 5 ? Moreover discuss difference between adsorption of chromium and precipitation of chromium ?

I am a student of MS Environmental Engineering and started my research phase. I am working on metal removal ( chromium iii ) by using activated carbon prepared from the agricultural feedstock. So...

01 March 2021 5,475 2 View

I have designed reflectarray element and feeding it though Horn Antenna on HFSS. After full wave simulation, I am not getting desired results?

I have designed reflectarray element to generate OAM beams at 5.8GHz and feeding it though Horn Antenna on HFSS. After full wave simulation, i am not getting desired results i.e Radiation pattern...

01 March 2021 9,701 5 View

Is there a method of determining feed digestibility without the need to re-pellet the feed?

I am aiming to determine the ADC values of a commercial fish feed, but I do not have a steam pelleter or extruder available to me. Ideally, the pellets could be coated with some inert marker....

28 February 2021 7,967 3 View

Benefits of the 24 welled plate?

We have always used the 96 welled plate, the 48 welled plate but apparently there is much evidence on the 24 welled plate and above all its benefits.It states it is the same you would use on ELISA...

28 February 2021 1,149 1 View

Can bacterial suspension be pipetted directly onto petri dish and agar poured onto it?

Hi, recently I encountered a protocol for plating which was not the usual method I have been practicing (pour LB agar onto plate, allow it to solidify, pipette bacterial suspension onto plate,...

28 February 2021 7,292 3 View

How can I assign a velocity along one direction to CO2 molecules in a molecular dynamics simulation using GROMACS?

Dear all, I am trying to perform a MD simulation about the interaction between CO2 and a polymer. I create my model, solvate it and perform the NVT and NPT equilibration. Now I am not able to...

26 February 2021 10,014 3 View