Please suggest the way and different parameters to be considered for fabrication of a glass micro model to be used in water flooding ?

More Rohit Kumar Saw's questions See All

How are iso-frequency contours plotted?

Let's say we have a standard, regular hexagonal honeycomb with a 3-arm primitive unit cell (something like the figure attached; the figure is only representative and not drawn to scale). The...

07 August 2024 1,937 1 View

How does high humidity affect the growth and development of crops?

10 July 2024 7,258 20 View

In what ways does high humidity impact the pollination process in agricultural plants?

10 July 2024 7,513 13 View

I have need a LPBF/SLM model on comsol multiphysics ?

In this model clearly understanding how to active one layer to another layer and how to add powder material properties step by step.

08 July 2024 6,147 0 View

Why hall bar fabricated using photolithography and sputtering are not showing continuity with contact pads?

I am fabricating the Hall bar (5 micron width and 35 micron length) of Ta(3nm)Co(4nm)Pt(5nm) using photolithoghaphy and sputtering. This Hall bar is connected by contact pads of Ti(10nm)/Au(60nm)...

29 June 2024 2,079 3 View

How do economic sanctions impact the foreign policy decisions of countries involved in geopolitical conflicts?

22 June 2024 7,923 4 View

What are the major challenges faced by small and marginal farmers in accessing credit and financial services?

19 June 2024 6,799 6 View

What are the primary obstacles in the implementation of sustainable farming practices across different regions of India?

19 June 2024 5,138 5 View

How can organic farming practices benefit crop diversification efforts in the arid regions of Punjab?

13 June 2024 1,724 4 View

What role can research institutions play in developing crop varieties suitable for the arid climate of Punjab?

13 June 2024 3,951 11 View

Fabrication of narrow glass capillary (inner diameter 200~500 nm)?

I need a very narrow glass capillary for my research. How can I make a glass capillary with an inner diameter of around 200 to 500 nanometers?

08 August 2024 8,915 0 View

How to understand this crystallographic phenomenon of low temperature crystals in zeolite?

During low-temperature testing, new diffraction peaks that appear could be indicative of several phenomena. In one of our tests, we observed notable new peaks around 40° and 45° in a specific...

06 August 2024 726 3 View

Is it possible to improve the reforming section of the Haber-Bosch process without using air separation units?

A typical reforming section in a large-scale Haber-Bosch process (Figure 1) comprises two reactors. A mixture of methane (CH4) and steam (H2O) is fed into a primary reformer to produce syngas via...

01 August 2024 7,051 5 View

In passive sampling, can polymer-lipid partition coefficients be applied independent of environmental salinity?

For example, if low-density polyethylene (LDPE) is equilibrated with PCB contaminated marine and freshwater sediments, can LDPE-lipid partition coefficients be used to obtain equilibrium...

28 July 2024 263 1 View

How to convert water conductivity in mS/cm to Salinity and TDS?

In order to test different water parameters I need to know how to convert conductivity to Salinity and TDS in ppm or ppt. Give me the reference please.

27 July 2024 2,414 2 View

Could GSH level be more in CCL4 rats than negative control rats?

i compare between the antioxidant and oxidative stress level between negative control rats (saline) and CCL4 intoxicated rats. i found the level of GSH and TAC is more in toxic group than normal....

26 July 2024 1,887 0 View

How do you decide an optimal AC amplitude for non-faradaic electrochemical impedance spectroscopy?

I work with planar interdigitated electrodes (IDEs). The finger width and the spacing between the fingers are 5 micron. The surface of the IDEs is coated by a non-conductive polymer layer...

16 July 2024 5,031 1 View

Does the potentiostat have to be in a fume hood when polymerising the PANI?

I will polymerise Aniline on ITO glass WE, using 1M of H2SO4 and a potentiostat. However, I am not sure if I have to do the electrochemical polymerisation inside a hood. Is it necessary? Is the...

10 July 2024 2,937 3 View

Where to source glass rings compatible with cell culture?

Hi all, I am looking glass cilinders that have an open flat bottom and top. Preferably with the inner diameter in the range of 2 cm. It's similar to the ones found on multi-electrode arrays for...

06 July 2024 5,846 1 View

What is alternative for PMMA?

If we want to introduce a material similar to polymethyl methacrylate "with the characteristics mentioned in the next paragraph" that can be added to a precursor and create a composite, which...

03 July 2024 2,371 1 View

Łukasz Gołek

What exactly do you mean as "water flooding" - water cooling during glass melting? Or something different?

Rohit Kumar Saw

Dear, Lukasz Golek water flooding is a secondary process used in enhanced oil recovery to extract oil by pressure maintenance in which we inject water in the reservoir to maintain the flow of oil to the surface.