QTL, recombination frection?

22 February 2021 2,588 2 View

What are the dimensions by which the independent variable (big data) can be measured, Knowing We using the questionnaire instrument?

We have a research project consisting of three variables where big data is the independent variable. Some previous studies showed that Volume, Variety, Velocity and Veracity Are the dimensions...

21 February 2021 8,133 2 View

How can we determine the band gap of a composite material that is made up of a composition of direct and indirect band gap semiconductor materials?

I have a direct band gap material and an indirect band gap material. If I made a composite of both through physical mixing. Then how can I determine the band gap of such a material as the Tauc...

17 February 2021 8,104 4 View

What Electrolyte Solution should be used for EIS and CV, While material I'm using is Carbon doped Titania as a counter electrode in DSSC?

Hope so, you are all fine, I want to perform EIS and CV of my material Carbon doped Titania as a counter electrode for DSSC, I just want to know what electrolyte solution and in what molar...

25 December 2020 7,095 3 View

How to determine the sample size for ANOVA in GPower?

Hi, I am going to execute an experiment with the four categorical variables (A=2 levels, B=2 levels, C=2 levels, D= 5 levels) and one dependent continuous variable. There are total of 40 groups...

19 December 2020 3,600 4 View

What are the free fee journal in Scopus or Clarivate classification deal with geotechnic ?

I want to introduce my manuscript to journal which is not take fee on publishing.

15 November 2020 609 3 View

Why the crystallographic plane (100) has higher growth rate than other planes such as (220), (111) in (100) oriented crystal?

Dear All, Here I have an interesting question that comes to me about crystallographic planes and growth rate. The literature survey shows, the (100)-oriented crystals the crystallographic plane...

06 November 2020 9,490 10 View

Can we co-relate that A-site vacancies are one of the main reasons for (110)-texture formation? But how?

A-site deficient 0.1BiScO3-BaTiO3 (BSBT) thin films were deposited on Pt/TiO2/SiO2/Si substrate by using PLD. XPS results revealed that A-site vacancies increase with the increase of deposition...

05 November 2020 9,281 1 View

Difference between Data-Driven Adaptive Robust Optimization and Adaptive Robust Optimization?

Could you make some points about the difference between Data-Driven Adaptive Robust Optimization and (classic) Adaptive Robust Optimization?

01 November 2020 9,653 3 View

Can anyone tell me that how to find dangling bond in GaN, AlN or AlGaN?

I want to know about the dangling bond? by which method we can find it, does its need some special type of characterization just like XRD etc... or method i want to find dangling bond effect in...

26 October 2020 1,938 6 View

Any suggestions for viable publications regarding the forcing schemes in TRT LBM?

I'm looking for publications regarding the Two-Relaxation Time Lattice Boltzmann Method's forcing schemes without passing through the Multi-Relaxation Time's full procedures I'm specifically...

23 March 2020 1,162 3 View

Is there not a common root of LBM and SPH modelling incompressible fluid flows?

Is there not a common root of Lattice Boltzmann Methods (LBM) and Smoothed-particle Hydrodynamics (SPH) modelling incompressible fluid flows? I see common grounds by means of a mesocopic...

30 December 2019 3,550 7 View

Is there not a common root of LBM and SPH modelling incompressible fluid flows?

Is there not a common root of Lattice Boltzmann Methods (LBM) and Smoothed-particle Hydrodynamics (SPH) modelling incompressible fluid flows? I see common grounds by means of a mesocopic...

11 December 2019 2,640 2 View

Is there anyone who could help in implementing outlet boundary condition using IB-LBM for external flow?

I have an IB_LBM SRT code on which velocity inlet and pressure outlet(Zou-He) Boundary conditions are applied for flow over a square. I want to simulate for higher Reynolds number on which this...

24 September 2019 7,979 3 View

Is there anyone who could help in implementing outlet boundary condition using IB-LBM for external flow?

I have an IB_LBM SRT code on which velocity inlet and pressure outlet(Zou-He) Boundary conditions are applied for flow over a square. I want to simulate for higher Reynolds number on which this...

08 September 2019 191 3 View

How can a two-phase system be immiscible in multicomponent Shan Chen Lattice Boltzmann Method?

The query arises different points of the model I am trying to explore which I am going to explain step wise as followed: (i) I am trying to simulate a two-phase immiscible flow in a porous media...

08 September 2019 5,040 1 View

How to visualize 3D arrays?

Hi, I am currently working on a numerical simulation of the flow of two fluids through porous digital rocks using C++. I have a binary file(1=rock,0=void) for the rock which has a 2D slice-based...

05 June 2019 7,843 5 View

Does anybody has implemented pressure inlet and outflow boundary condition in Shan-Chen based LBM together?

Hello, I have a series of problems during implementing Pressure inlet (PI) and Outflow in Shan-Chen based LBM. When I use PI and pressure outlet(PO), there is no problem. The velocity inlet and...

05 June 2019 4,396 5 View

Is there a far field boundary condition in LBM?

I want to know that can we model "far field boundary condition" by LBM? For example when we want to model a thin gas jet in a very big domain such that the jet has no effect on boundaries, what...

14 February 2019 4,080 3 View

How to define a square geometry in the domain for simulation using LBM?

As we can define a circle by using an equation of circle x^2+y^2=r^2 in programming on visual studio to place a blunt body in the way of domain. How can I define a square in the same way as a...

01 January 2019 3,126 2 View