Please, how can one simulate SEIR model using ADM code?

01 October 2022 1 2K Report

Please, I need a Matlab code for simulating application of Adomian decomposition method (ADM) for solving a SEIR epidemic model. Thanks in anticipation as I await positive response from you (scholars) all.

Hassan Nasser

Dear Emeka Emmanuel Otti:

You can benefit from these valuable Links about your topic:

@https://www.researchgate.net/topic/Adomian-Decomposition-Method

@https://github.com/mrc-ide/squire

@https://www.ncbi.nlm.nih.gov/pmc/articles/PMC7523173/

I hope it will be helpful ..

Best wishes ..

Badges
Science topic

Similar topics
Computer Science
Program

More Emeka Emmanuel Otti's questions See All

Hi, I Am Currently Researching On Wind Energy In Nigeria. Pls, Which Software Can Plot This For Me Or How Can I Get The Same Plot For Nigeria?

This is a plot of wind speed in America at 100m and 80m. what software can i use to plot this

17 November 2020 914 8 View

I am doing ansys structural analysis of Tyre ,how can i model air pressure inside the Tyre ?

i am currently running an ansy structural analysis of a vehicle tyre ,how can i model air pressure inside the tyre?

20 December 2018 5,767 4 View

Sociology of correction

Am an undergraduate student of sociology preparing for a research on correction technic in modefying criminal behaviour of criminals. You suggestion are wellcomed

08 May 2011 2,742 1 View

How to code open-ended questions in SPSS?

Hello all, In SPSS I am going to code 2 open-ended questions. I have already read all the answers and I made a list of the most important categories to which I can code the answers. This question...

02 March 2021 1,757 4 View

How can I integrate a routing protocol in a tiny device (e.g. Raspberry Pi)?

Hi Community, I'm facing the issue of integration/compiling a new routing protocol in a WSN simulator. The final goal is to successfully add, configure this routing protocol in hardware devices...

01 March 2021 9,332 6 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

Timeout error!! Processor in the loop (PIL) using STM32F4 Matlab 2018a?

Dear Researchers I am trying to perform a PIL simulation using STM32F4 Discovery board and comunication serial USB TO TTL. During simulation I receive the following timeout error: An error...

01 March 2021 2,327 1 View

How to eliminate Steady state error from Reinforcement learning genetic algorithm code?

The following code (see 1st 2 images attached) is used to produce PID controller values that are designed to control the system (G). The code finds the PID controller values (noted as k) by using...

28 February 2021 6,560 14 View

How to prevent ANFIS Model from negative prediction values in MATLAB?

I have input and output data set for "ANFIS modeling in MATLAB", and I am getting some negative predicted values of output in testing. However, the predicted values of output in training are...

28 February 2021 3,459 3 View

How to modify Johnson cook equation in ABAQUS?

I wanted to add an extra parameter to the existing Johnson cook equation in the ABAQUS simulation. How to add those extra parameters. Ref: A modified Johnson-Cook material model with strain...

28 February 2021 4,841 3 View

How to improve and implement WBAN MAC and Radio modules under Castalia 3.2 ?

Hello researchers, Hello Castalia3.2 researchers I am a beginner with Castalia, I work on optimization of RFID systems used in wireless body networks. I simulated a WBAN with 10 nodes and one...

28 February 2021 400 1 View

How can we simulate an hyperelastic-viscoelastic behavor with Ansys APDL?

I am working on modeling and simulation of biomecanical material behaviour, I have succeded on simulating skin using anisotropic hyperelastic material, on APDL and in our lab's finite element...

28 February 2021 552 3 View

How to find the right number of integration points in second order 3d finite elements?

I am familiar with finite element simulations and numerical schemes like the Gauss Legendre quadrature. I also know that the Gauss integration yields exact values for polynomials up to degree 2n-1...

27 February 2021 6,818 3 View