How to remove unedited version of the manuscripts from research gate?

Our manuscript was published ahead of print. The edited and revised version is now available. How do I remove the old version of the manuscript from the research gate?

01 February 2021 5,965 1 View

How to prevent false negative FISH results?

I am analyzing data from a FISH experiment and notice that there are false negatives. What is the best option to change in the experimental set up to avoid this from happening?

04 October 2020 5,777 1 View

Clarification on Shapiro-wilk sig. , skewness and kurtosis?

Hello, Maybe is a bit silly question but, I have a variable (N=78) and on shapiro-wilk test the sig. is .008 which is just over (greater) than 0.05 meaning that is just about normally...

29 August 2020 1,384 4 View

How do you average log CFU/ml?

Do you first calculate the average of all the CFU and then sub it into the equation ? OR Do you calculate each individual log CFU/ml and then average that?

19 March 2019 7,956 6 View

What is the general upper detection limit CFU/ml for Enterococcus faecium?

How do you determine the upper detection limit for E. faecium? If there are too many to count on the plate, can I suggest that there are >25,000 CFU/ml for example? - or would that be too much

02 March 2019 1,261 1 View

How do you perform a Mann-Whitney U test when trying to calculate the average CFU/ml?

I have a treated and a control condition of agar plates. I counted the number of colonies and wanted to carry out a mann whitney test. Do I carry out the mann whitney test using the counted...

02 March 2019 4,830 1 View

How do you average log CFU/ml?

Do you first calculate the average of all the CFU and then sub it into the equation ? OR Do you calculate each individual log CFU/ml and then average that?

02 March 2019 1,412 7 View

Do different alcohols disinfectants act on the same mechanisms to kill bacteria?

For example, do isopropanol/1-propanol/ethanol alcohol based hand rubs all use the same mechanisms to kill bacteria? Do they all just disorganize lipid membranes, denature proteins, and...

02 March 2019 8,814 3 View

How to find x-ray structures that have been fully solved for homology modelling?

I'm trying to use homology modelling to find the structure of the N-terminus of a protein which is thought to contribute to its hetero-oligomeric structure. However, I can't find an x-ray...

24 December 2018 6,810 3 View

What causes bacteria to have sharp/fuzzy zone of inhibitions on disc susceptibility plates?

Zone of inhibitions sometimes appear fuzzy/sharp with different antibiotic discs on the same agar plate, what are the explanations for this? Also, how important are these when determining the...

10 November 2017 8,676 0 View

How to analyze a particular region of my simulation box in GROMACS?

Hi, I am using GROMACS 5.1.4 to simulate water in contact with a surface. I am only interested to calculate some properties of water near the surface. Let's say at a distance of x nm from the...

03 March 2021 9,989 2 View

How to get onecolumn document from standard IEEE ACCESS LateX template?

I have prepared a manuscript in IEEE Latex template, but for some purpose, I need to prepare a word file as well (detailed format is not required). Compared to two column .tex file, one column...

02 March 2021 1,830 3 View

How can the modification of garden soil cause global warming?

Hello, I am working on a soil project and I found a primary research article that tests how the modification of agricultural soil can cause global warming, using a thermal collector, however I...

02 March 2021 7,161 3 View

Does anyone know how to plot my station to a section plot on Ocean Data View (ODV)?

I made a vertical section plot with WOA .nc file on ODV, and now I want to plot my stations (csv. file) in it. Does anyone know how to import my points to the section? They are two different...

01 March 2021 3,610 1 View

Does anyone know to clarify these changes?

01 March 2021 1,290 2 View

How can I convert .vesta file to a .cif file?

I've used the "export data" option in Vesta software to convert my unit cell into a cif file however when I use that cif in atomsk it shows error such as "can't read the position of atom 0". If I...

28 February 2021 4,966 3 View

How can we use a hybrid element in Abaqus Dynamic/Explicit for impressible materials?

Hi, all! How can we use a hybrid element in Abaqus Dynamic/Explicit for impressible materials? I have not find the choice for explicit element in Abaqus CAE. I am wondering whether it is possible...

25 February 2021 9,936 2 View

No title

25 February 2021 5,713 1 View

Anyone that can help with Maxquant TMT16plex which is missing?

Hi I am very new to proteomics analysis. I have got raw files from core facility running thermofisher TMT 16plex 4 hours. I cannot find on maxquant the option TMT16Plex there is only up to 11...

25 February 2021 1,675 3 View

How to search for crystal structure for material with atomic position labelled?

I am using the crystallographic open database and materials project to search for cif file but the exact structure is not mentioned or how can I deduce that the given structure and atomic position...

23 February 2021 6,723 2 View