Why the results when using wall thickness and when using shell conduction are different in ansys fluent?

Actually, I am running cfd simulation for a heat exchanger which has two fluids one hot and other one is cold fluid. there is a solid domain between them, which I removed and instead I have used...

01 March 2021 9,537 2 View

How much pressure we can reduce at the outlet to avoid Reverse Flow?

I am simulating Heat Exchanger. I have tried and tested all the methods to resolve this issue from the internet like refining mesh, improving skewness and orthogonal quality ,extending outlet to...

01 March 2021 6,985 3 View

Could you please recommend some good journal that accept very long revie papers (approximately 6000+ words) in neurosurgery, cancer biology ?

Could you please recommend some good journal that accept very long revie papers (approximately 6000+ words) in neurosurgery, cancer biology ?

01 March 2021 8,087 3 View

Does anyone know to clarify these changes?

01 March 2021 1,290 2 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

Errors in DNA sequences?

I am trying to better understand the scope of DNA replication and sequencing errors, e.g. 1. I have seen similar error rates of 10e4 to 10e5 for cell & instrumental DNA replication,...

24 February 2021 4,397 3 View

Does PHA-P stimulate the proliferation of lymphocytes from mice?

Hello, I will start performing MLR using lymphocytes from mice's spleen and I would like to know the better way for the stimulation. If is using PHA-P or CD3/CD28? I would like to know as well if...

23 February 2021 5,476 4 View

Could not amplify CD28 and CD3z ectodomain from cDNA of Jurkat Cells ?

For my experiments, I have to express ectodomains of human CD28 and CD3z. As a source, I extracted RNA from Jurkat cells and verified the quality of RNA on the gel. I, then, prepared cDNA using...

23 February 2021 7,051 4 View

Best FE Program for Concrete Strengthened with FRP Sheets?

Colleagues, I have been using ANSYS to model concrete strengthened FRP sheets, but less than happy with it. Any has recommendation for efficient, easy to use FE program for modelling concrete...

22 February 2021 7,528 3 View

What is the status of bread making and more bakery foods with the use of insect flour/powder?

Insects have been consumed by human diet since prehistoric times. At present, the idea of looking at insects as food has been getting traction worldwide, also in response to increasing food...

03 March 2021 6,223 5 View

Which is the most efficient etching solution for nickel based alloys?

Which solution reveals the microstructure and features of nickel-based alloys?

02 March 2021 2,221 3 View

How to grow E.coli on the low salt LB agar plate with 50 or 100ug/ml of Blasticidin?

Hello, I would like to ask how to grow E.coli which resists 50 or 100ug/ml of Blasticidin. I have tried many methods by using low salt Luria-Bertain(LB) agar plate. However, no colonies grow. Let...

01 March 2021 2,027 2 View

Which reagent is best among 'Dimethylglyoxime" and "Dithiothreitol" for spectroscopic determination of Nickel ?

What I think is Dithiothreitol. As it is water-soluble and does not form a precipitate. But, the thing is it contains sulphur which is quite hazardous to aquatic animals.

01 March 2021 8,374 4 View

Why is my platinum counter electrode getting dirty during electrodeposition?

I am conducting anodic electrodeposition of MnO2 onto a stainless steel substrate, using a platinum strip as a counter electrode. This is done galvanostatically, with the current held between 5...

27 February 2021 1,829 3 View

Have anyone checked before Cyclic voltammograms of intial ITO substrate and E-teck?

As a beginner in electrochemistry, I tried to obtain cyclic voltamograms of commercial anatase powder deposited on an ITO substrate or on Eteck. After several attempts, I noticed that my cyclic...

23 February 2021 3,175 3 View

How to reduce static electricity of powder after lyophilization?

I am working on synthesizing and then purifying peptides using the SPPS system. After purification of the peptide, the peptide powder is obtained using a freeze dryer. When measuring the powder,...

22 February 2021 10,099 5 View

What kind of steel moulds are used for hot pressing metal powders?

My main concern is that the metal powders should not weld to the mold surface and I should easily be able to eject out the pressed samples. I am looking for alternative for graphite moulds. The...

22 February 2021 2,965 4 View

How can I measure the thickness of thin layers deposited on textured glass susbtrates?

I want to measure the thickness of aluminum oxide and titanium oxide layers deposited on textured glass substates. The layer thicknesses are typically below 100nm.

21 February 2021 5,465 4 View

How to Study a proton NMR of Graphene prepared by Electrochemical Exfoliation technique?

I performed a Proton NMR of graphene powder prepared by electrochemical exfoliation technique. It shows some peaks. But I can't understand it.

21 February 2021 8,947 3 View